Thank you ladybug!
And its very sharp from box..
Spyderco Manix 2 Lightweight
Re: Spyderco Manix 2 Lightweight
Is WD-40 good for maintenance and lubrication of Manix2 ?
Re: Spyderco Manix 2 Lightweight
personally, i wouldn't use wd-40. i use frog lube paste on the blade if i'm worried about corrosion because it's food safe. i use either kpl or daiwa reel oil on the pivot, bearing, and spring if necessary.
keep your knife sharp and your focus sharper.
current collection:
C191GP, C36GMCBK2, C11ZFRDBBK, C267BK, C36MCW2, C258YL, C253GBBK, C258GFBL, C101GBBK2, C11GYW, C11FWNB20CV, C101GBN15V2, C101GODFDE2, C60GGY, C149G, C189, C101GBN2, MT35, C211TI, C242CF, C217GSSF, C101BN2, C85G2, C91BBK, C142G, C122GBBK, LBK, LYL3HB, C193, C28YL2, C11ZPGYD, C41YL5, C252G, C130G, K08BK, PLKIT1
spyderco steels:
M398, H2, CPM 20CV, CPM 15V, CTS 204P, CPM CRUWEAR, CPM S30V, N690Co, M390, CPM MagnaCut, LC200N, CTS XHP, H1, 8Cr13MoV, GIN-1, CTS BD1, VG-10, VG-10/Damascus, 440C, MBS-26
current collection:
C191GP, C36GMCBK2, C11ZFRDBBK, C267BK, C36MCW2, C258YL, C253GBBK, C258GFBL, C101GBBK2, C11GYW, C11FWNB20CV, C101GBN15V2, C101GODFDE2, C60GGY, C149G, C189, C101GBN2, MT35, C211TI, C242CF, C217GSSF, C101BN2, C85G2, C91BBK, C142G, C122GBBK, LBK, LYL3HB, C193, C28YL2, C11ZPGYD, C41YL5, C252G, C130G, K08BK, PLKIT1
spyderco steels:
M398, H2, CPM 20CV, CPM 15V, CTS 204P, CPM CRUWEAR, CPM S30V, N690Co, M390, CPM MagnaCut, LC200N, CTS XHP, H1, 8Cr13MoV, GIN-1, CTS BD1, VG-10, VG-10/Damascus, 440C, MBS-26
Re: Spyderco Manix 2 Lightweight
I have experienced WD-40 to get gummy with time.
Steel novice who self-identifies as a steel expert. Proud M.N.O.S.D. member 0003. Spydie Steels: 4V, 15V, 20CV, AEB-L, AUS6, Cru-Wear, HAP40, K294, K390, M4, Magnacut, S110V, S30V, S35VN, S45VN, SPY27, SRS13, T15, VG10, XHP, ZWear, ZDP189
Re: Spyderco Manix 2 Lightweight
Just my experience, but I would not lubricate the Manix 2 LW at all.
I did in the beginning with my REX 45, cause I was worried about potential rust in the pivot area with that tool steel and given that- unlike you with the now screwed model - I cannot disassemble my Manix (pins).
Turned out to be not necessary at all - action good without lubrication, no rust as far as I can tell (i could imagine that the pivot area has kind of a "self cleaning" function due to the frequent rotation and slight friction. Just a guess though).
IF I lubricate a folder: I have good luck with Victorinox multitool oil, can only recommend it.
Top three going by pocket-time (update October 25):
- EDC: Endela SE (K390). Endela SE (VG10), Manix 2 LW (REX45)
- Mountains/outdoors: Pac.Salt 2 SE (LC200N), Salt 2 SE (LC200N), Pac.Salt 1 SE (H1)
- EDC: Endela SE (K390). Endela SE (VG10), Manix 2 LW (REX45)
- Mountains/outdoors: Pac.Salt 2 SE (LC200N), Salt 2 SE (LC200N), Pac.Salt 1 SE (H1)
