Spyderco Forums

I saw a while back that someone had asked about getting some of the holes that are cut out of the spydie blades and Spyderco replied that they would do it if someone agreed to distribute them.I never saw anything else about it so I emailed Joyce and asked if I could do it.She spoke with Sal and said yes but they have sharp edges and bits of metal still on them and needed to be cleaned up before being sent on.I said I would clean them up and now they are on the way to me.

So if anyone wants some,not sure what I can send to each forumite until I see whats in the package.Best case would be one small,med,and large.

All I ask is that if you want some please send me a SASE,2 stamps on it should cover it and post here that you want them.

Now for forumites that live outside the US.It will be much harder for you to do the SASE so I will cover getting them to you,just send me your shipping info.

Please give Joyce and the Spydie crew a big thank you for makeing this happen.

I will post my address so you can send me the SASE.I can't think of any reason not to post it.If you know someones name you can get there address in seconds on the net.If anyone knows any reason for me not to post my address please let me know.

JEFF SMITH

702 RUSSEL AVE

HARRIMAN TN 37748

I really wish I could cover the shipping of them too but I expect there will be tons of interest in these.

Thanks and Merry Christmas to all.



<img src=http://www.bladeforums.com/forums/image ... rforum.gif

Jeff,that was me.I never heard anything more on this subject until today.I wanted one or more to make tie tacs.I just mailed you an envelope.Thanks.tom.

N.R.A. LIFE MEMBER...Thig crioch air an t-saoghail, ach mairidh gaol 's ceol.

Edited by - deputy tom on 12/5/2003 9:34:57 AM

Very cool Jeff! Thanks for the effort and thanks to the Spyderlords for the hole-y donations. <img src="spyder.gif" width=15 height=15 align=middle border=0> My envelope is coming your way <img src="spyder.gif" width=15 height=15 align=middle border=0>

-Rorschach :][: <a href= http://www.scarysharp.com>HOS</a>

Thanks going on monday to laredo to send you the envelope thanks for a holey cristmas

Slowly one at a Time, but someday...

Hello <img src="smile.gif" width=15 height=15 align=middle border=0>,
im sorry, but i do not understand, its funny ...eeee..what holes ???
Holes ???

And what is SASE ?

Simona V. :: joyful girl from the Prague, Czech Republic, www.myspyderco.tk

Edited by - Barefoot_Simona on 12/5/2003 11:11:43 AM

Hi Simona the holes are the piece of metal that is left when the cut it from the metal to make te opening mecanism

and a SASE envelope ill learn monday what it is

Slowly one at a Time, but someday...

Self
Addressed
Stamped
Envelope

Jeff, what a cool gesture.
I'll get an envelope to you!
Can we pick sizes & steel type? <img src="wink.gif" width=15 height=15 align=middle border=0><img src="smile.gif" width=15 height=15 align=middle border=0>

Ted

Its Alive!

Knife Knut on a shoestring budget.

finally, it's alive... our idea lives!
*insert evil laughter and lighting*

Jeff, have my addy or need it again?

<img src="http://www.members.shaw.ca/pjharyett/sp ... pyder5.gif">
Mei Fides, Mei Victus
Coffee Before Conciousness
<a href=http://www.members.shaw.ca/pjharyett>My Homepage </a>

Hi patogordo, you wrote : ..the holes are the piece of metal that is left when the cut it from the metal to make te opening mecanism


im sorry, im moron <img src="smile.gif" width=15 height=15 align=middle border=0> ..i still not understand, ..what make opening mechanism and which holes ??

ahh, SASE, now i know, thanks <img src="smile.gif" width=15 height=15 align=middle border=0>


Simona V. :: joyful girl from the Prague, Czech Republic, www.myspyderco.tk

Edited by - Barefoot_Simona on 12/5/2003 4:10:59 PM

See the hole in your blade? It's the piece of metal they cuy out to make the hole. Think doughnut hole.

Aha!....now i know! Please,i want one too! <img src="smile.gif" width=15 height=15 align=middle border=0><img src="smile.gif" width=15 height=15 align=middle border=0>Its possible? ..Big, size from Military...

Simona V. :: joyful girl from the Prague, Czech Republic, www.myspyderco.tk

Is there any way of differentiating between steels on these? I'd like to get a few to look at the grain size and structure under a SEM for comparison of the steels. If not, I'll still take a few.

This is cool. I just might go for some but they really can't be called holes though can they?
They are what was left to make a hole right?

Maybe they could be incorporated in a lanyard for your knives-just a thought....

ken

they are slugs cut from the hole in your knife... if you watch the video(I know it's on the dealer one), they show in the first 5-10seconds what we're asking for.
going to be a rough circle, with a line doing 1 radius on it. Nothing pretty, but it's a peice of curiousity(just so you can say you have one).

http://www.spyderco.com/forum/Topic.asp ... kies+Forum

<img src="http://www.members.shaw.ca/pjharyett/sp ... f"><br>Mei Fides, Mei Victus<br>Coffee Before Conciousness<br> <a href=http://www.members.shaw.ca/pjharyett>My Homepage </a>

Edited by - vampyrewolf on 12/5/2003 6:26:34 PM

So...simply you give this thing to back to blade hole, and you will own knife without hole... <img src="smile.gif" width=15 height=15 align=middle border=0> called NONHOLE Spyderco ...
Reg.patent No.007 - knife, what you cant open like a onehand ...
Its designed for lands, where are restricted onehands ...


Damnt, where is hole for opening, this is not Spyderco !
Yeees,is, but it is masked ...
????...



Simona V. :: joyful girl from the Prague, Czech Republic, www.myspyderco.tk

wholes

steel is unforgiving... sharp steel even more so

Got them today.They are all the same size.I will send 2 to everyone who asks.
If you are in the US please send a SASE and if you are out side the US email me your address.

<img src=http://www.bladeforums.com/forums/image ... rforum.gif

I turned on my computer tonight and for some reason everything was reset to the defaults.So if anyone sent me email to day please resend,it may have been lost.

<img src=http://www.bladeforums.com/forums/image ... rforum.gif