MT36P – K294 MICROCLEAN Mule Team Dropping Soon!
- elmeringalo
- Member
- Posts: 126
- Joined: Tue Sep 02, 2014 6:50 am
- Location: Spain, Europe, Earth
Re: MT36P – K294 MICROCLEAN Mule Team Dropping Soon!
Today has been very fast. I have taken two directly, without waiting. thanks spy
No por mucho tempranar, amanece mas madrugo
Re: MT36P – K294 MICROCLEAN Mule Team Dropping Soon!
It kinda seems like it depends on the hype around the steel. MagnaCut and 15V flew out of stock. I think more people would be clamoring for the K294 if they knew it was basically 10V.Bolster wrote: ↑Tue Aug 22, 2023 11:14 amramblinwreck wrote: ↑Tue Aug 22, 2023 10:14 amDo these usually sell out? I see a few others from earlier this year still available.
Eventually, yes. The amount of time it takes for a mule to sell out varies widely, based in large part on desirability of the steel, which is in turn affected by hype and buzz. The Magnacut sold out almost immediately. The K294 looks to be a true winner of a steel with its excellent balance of toughness for its very high edge retention range...but nobody's been out there recently, promoting K294 (though Phil Wilson likes it). Given its high initial price and remarkable properties, I think it's going to be a bit of a sleeper steel, probably highly valued once the stock is gone. That the K294 comes quickly on the heels of several previous mules may also slow its sales somewhat.
I've seen other forumites opine that the AEB-L mule is similar...a sleeper steel that will become quite desirable when the stock is depleted.
Of course, this is all conjecture on our parts. But just try to purchase some of the well-regarded steels in by-gone mules and you'll be shocked at how much you have to spend to get one.
- legOFwhat?
- Member
- Posts: 3143
- Joined: Mon Jul 09, 2018 5:58 am
- Location: Kentucky; Earth
Re: MT36P – K294 MICROCLEAN Mule Team Dropping Soon!
I think in part that is why the PMA11 sat around for so long and that might be better than this...PD#1 probably suffered for the same reasons.kennbr34 wrote: ↑Tue Aug 22, 2023 12:38 pmIt kinda seems like it depends on the hype around the steel. MagnaCut and 15V flew out of stock. I think more people would be clamoring for the K294 if they knew it was basically 10V.Bolster wrote: ↑Tue Aug 22, 2023 11:14 amramblinwreck wrote: ↑Tue Aug 22, 2023 10:14 amDo these usually sell out? I see a few others from earlier this year still available.
Eventually, yes. The amount of time it takes for a mule to sell out varies widely, based in large part on desirability of the steel, which is in turn affected by hype and buzz. The Magnacut sold out almost immediately. The K294 looks to be a true winner of a steel with its excellent balance of toughness for its very high edge retention range...but nobody's been out there recently, promoting K294 (though Phil Wilson likes it). Given its high initial price and remarkable properties, I think it's going to be a bit of a sleeper steel, probably highly valued once the stock is gone. That the K294 comes quickly on the heels of several previous mules may also slow its sales somewhat.
I've seen other forumites opine that the AEB-L mule is similar...a sleeper steel that will become quite desirable when the stock is depleted.
Of course, this is all conjecture on our parts. But just try to purchase some of the well-regarded steels in by-gone mules and you'll be shocked at how much you have to spend to get one.
-Larry
Hebrews 13:6 So we may boldly say: “The Lord is my helper; I will not fear. What can man do to me?”
MNOSD #0049
Hebrews 13:6 So we may boldly say: “The Lord is my helper; I will not fear. What can man do to me?”
MNOSD #0049
Re: MT36P – K294 MICROCLEAN Mule Team Dropping Soon!
![Image](https://i.imgur.com/RfFVbKq.png)
- I welcome dialog, as long as it remains cordial, constructive and is conducted in a civilized manner. - Titanic: Blood & Steel
- You can fool some of the people all of the time, and all of the people some of the time, but you cannot fool all of the people all of the time. - Abraham Lincoln
- legOFwhat?
- Member
- Posts: 3143
- Joined: Mon Jul 09, 2018 5:58 am
- Location: Kentucky; Earth
Re: MT36P – K294 MICROCLEAN Mule Team Dropping Soon!
![Image](https://i.imgur.com/8GBc3col.jpg)
-Larry
Hebrews 13:6 So we may boldly say: “The Lord is my helper; I will not fear. What can man do to me?”
MNOSD #0049
Hebrews 13:6 So we may boldly say: “The Lord is my helper; I will not fear. What can man do to me?”
MNOSD #0049
Re: MT36P – K294 MICROCLEAN Mule Team Dropping Soon!
It was really tempting not to get a K294 and a T15, but they seem like they'd be so similar that I just couldn't justify it.
Still making up my mind on the AEB-L. Having a super tough, super fine-grained low alloy steel seems like it would be good to compare against high-alloy carbide rich steels, but I still haven't heard official figures on what the HRC of it is and I already have plenty of 1/8" carbon steel blades.
-
- Member
- Posts: 1391
- Joined: Thu Mar 25, 2021 10:06 am
- Location: Earth probably?
Re: MT36P – K294 MICROCLEAN Mule Team Dropping Soon!
Did my civic duty. Been wanting a 10V class fixed blade of this size so this worked well for me. Even waited until afternoon.
Because desolate places allow us to breathe. And most people don't even know they're out of breath.
MNOSD member #0035
MNOSD member #0035
- Deadboxhero
- Member
- Posts: 2178
- Joined: Tue Mar 01, 2016 4:35 am
- Contact:
Re: MT36P – K294 MICROCLEAN Mule Team Dropping Soon!
The AEB-L is 62-63 HRC
Which is the highest hardness you'll find in a AEB-L production knife available currently on the market.
Re: MT36P – K294 MICROCLEAN Mule Team Dropping Soon!
Thanks manDeadboxhero wrote: ↑Tue Aug 22, 2023 6:02 pmThe AEB-L is 62-63 HRC
Which is the highest hardness you'll find in a AEB-L production knife available currently on the market.
Re: MT36P – K294 MICROCLEAN Mule Team Dropping Soon!
kennbr34 wrote: ↑Tue Aug 22, 2023 3:30 pm
It was really tempting not to get a K294 and a T15, but they seem like they'd be so similar that I just couldn't justify it.
Still making up my mind on the AEB-L. Having a super tough, super fine-grained low alloy steel seems like it would be good to compare against high-alloy carbide rich steels, but I still haven't heard official figures on what the HRC of it is and I already have plenty of 1/8" carbon steel blades.
Same here….got a T15 for my first mule, was all set to get a ‘10V’ in the K294 today. But, I’ve cut like 2 boxes and 1 piece of tape in a month, LOL. I’m a retired city-dweller, why exactly I’m hunting for supersteels is a mystery, and would I even notice a difference in my usage? I could’ve cut those 2 boxes and piece of tape with a D2 folder
Anyway, mules are really cool….glad I got one. However, adding more doesn’t make sense FOR ME
.
Re: MT36P – K294 MICROCLEAN Mule Team Dropping Soon!
Yeah, people either didn't buy it, or bought two.
There's been a lot of competition this month to drain people's wallets, so timing might be an issue.
Re: MT36P – K294 MICROCLEAN Mule Team Dropping Soon!
Why is K294 more expensive? It's just a rip off of Crucible's CPM 10V. The R&D cost should be small; just read Crucible's patent from 1978. If I recall, the CPM 15V mule was cheaper and it has 5 more Vs.
- standy99
- Member
- Posts: 2217
- Joined: Sat Jul 22, 2017 11:07 am
- Location: Between Broome and Cairns somewhere
Re: MT36P – K294 MICROCLEAN Mule Team Dropping Soon!
Putting your own handle on them and making your own sheath it’s about the price it costs
![winking tongue :winking-tongue](./images/smilies/winking-face-with-tongue.png)
Couple of clamps a saw, also a file or two and some sandpaper and epoxy is how I started.
Im a vegetarian as technically cows are made of grass and water.
Re: MT36P – K294 MICROCLEAN Mule Team Dropping Soon!
Yeah, I’d probably actually like doing it….as a retired dentist, OCD tinkering with my hands and creating shapes is pretty natural. However, between tools, parts, materials, and a tendency to want the best results it may be a rabbit hole I’m not ready to go down
.
Re: MT36P – K294 MICROCLEAN Mule Team Dropping Soon!
I purchased a K294 Mule today and am really excited to put some hickory, maple, or walnut wood handles on it. I put hickory handles on the 15V mule I purchased and have really enjoy the experience. Spyderco and BBB did a wonderful job with 15V, I have found it to be very tough considering the hardness.
I used hand files and a small fixed blade to shape my handles. I love the Mules, as it gives you a chance to make the knife your own. I also purchased a leather stealth with each knife and have found it perfect for my EDC around the farmstead.
I would really like to purchase a AEB-L Mule as well. Like so many of you my knife funds are not endless. I have two custom knives I really want to purchase and the AEB-L Mule will hopefully happen in the next 4 weeks.
I want to thank all those who are involved in the making of the Mules!
I used hand files and a small fixed blade to shape my handles. I love the Mules, as it gives you a chance to make the knife your own. I also purchased a leather stealth with each knife and have found it perfect for my EDC around the farmstead.
I would really like to purchase a AEB-L Mule as well. Like so many of you my knife funds are not endless. I have two custom knives I really want to purchase and the AEB-L Mule will hopefully happen in the next 4 weeks.
I want to thank all those who are involved in the making of the Mules!
Re: MT36P – K294 MICROCLEAN Mule Team Dropping Soon!
Erion929 wrote: ↑Tue Aug 22, 2023 8:24 pm
Yeah, I’d probably actually like doing it….as a retired dentist, OCD tinkering with my hands and creating shapes is pretty natural. However, between tools, parts, materials, and a tendency to want the best results it may be a rabbit hole I’m not ready to go down
.
Respectfully disagree, doctor! If you have dentistry skills, you would love making complete mules, would be a natural at it, and the tool-up is not large. Achieving the best results is what makes it fun. You maybe won't get there on your first try but you'll enjoy the challenge. If you are OCD like me, make scales that screw in place rather than epoxy--then you can re-do whatever you don't like. Review Xplorer's tutorials in the Mule subforum on how to haft a mule and how to make a Kydex sheath, and have some fun, put your skills to use.
Steel novice who self-identifies as a steel expert. Proud M.N.O.S.D. member 0003. Spydie Steels: 4V, 15V, 20CV, AEB-L, AUS6, Cru-Wear, HAP40, K294, K390, M4, Magnacut, S110V, S30V, S35VN, S45VN, SPY27, SRS13, T15, VG10, XHP, ZWear, ZDP189
- standy99
- Member
- Posts: 2217
- Joined: Sat Jul 22, 2017 11:07 am
- Location: Between Broome and Cairns somewhere
Re: MT36P – K294 MICROCLEAN Mule Team Dropping Soon!
Erion929 wrote: ↑Tue Aug 22, 2023 8:24 pm
Yeah, I’d probably actually like doing it….as a retired dentist, OCD tinkering with my hands and creating shapes is pretty natural. However, between tools, parts, materials, and a tendency to want the best results it may be a rabbit hole I’m not ready to go down
.
Basically a dentist drill
![Image](https://files.catbox.moe/y4xxoq.jpeg)
Im a vegetarian as technically cows are made of grass and water.
-
- Member
- Posts: 3001
- Joined: Fri Sep 24, 2004 10:33 am
- Location: Longmont, CO USA
- Contact:
Re: MT36P – K294 MICROCLEAN Mule Team Dropping Soon!
Dear Nathan21:
Welcome to the Spyderco Forum.
Stay safe,
Mike
Welcome to the Spyderco Forum.
Stay safe,
Mike
Re: MT36P – K294 MICROCLEAN Mule Team Dropping Soon!
Steel goes from Germany (Bohler K294) to Japan and then to SFO to be sold. So quite a bit of travel. Then factor in time and labor for this material which would be a little more difficult to work with than some other materials (heat treating, sharpening, etc.), and the price adds up.
- elmeringalo
- Member
- Posts: 126
- Joined: Tue Sep 02, 2014 6:50 am
- Location: Spain, Europe, Earth
Re: MT36P – K294 MICROCLEAN Mule Team Dropping Soon!
![winking tongue :winking-tongue](./images/smilies/winking-face-with-tongue.png)
Putting your own handle on them and making your own sheath it’s about the price it costs
![winking tongue :winking-tongue](./images/smilies/winking-face-with-tongue.png)
[/quote]
That is assuming that the material of the handle, the cover and the tools are given to you
No por mucho tempranar, amanece mas madrugo