Spyderco Forums

I would make a Para 3:
ball bearing lock
G10
S35vn
and a sub 3in blade without a finger choil.

any one else?

Police3 w/ solid Super Blue at 1.7mm to 1.3mm and dark blue G10.

or

Para2 in M4 or Cruwear.

Sage 5

G10 handles and compression lock
Keep every thing else standard Sage

1) Caly 4.0 (4 inch blade), dark earth G10, wire clip, M4 steel

2) H1 Dragonfly Hawkbill SE

3) Lil' Ayoob. Same as G10 version but 2/3 size of the original (think PM2 to Millie)

G-10 Manix 2 in s110v with skeletonized liners. The inability to wash through the inside is my only complaint about the awesome LW version.

TomAiello wrote:G-10 Manix 2 in s110v with skeletonized liners. The inability to wash through the inside is my only complaint about the awesome LW version.

I agree; I would like to see torx screws instead of rivets on the LW Manix 2.

As for a new model I would like either:

- Native 5 with CBBL or compression lock; no swedge

or

- Mini Manix 2 with < 3" blade and narrower profile. Basically a Spyderco Embassy with CBBL.

1.) Superblue Spyderhawk, FFG, 2.5mm, solid blade, solid G10 handles (navy blue or deep green), PE

2.) A.T.R. SUPER-SALT, Ti handles (stonewashed), 3mm, high hollow, less swedge, Ti clip, H1 blade (stonewashed), SE

3.) Kiwi 5, 3" ZDP-189 blade, 2mm, HG, Bio-blue handle, copper or timoku or timascus inlay

i am glad to see i am not the only one that thinks of these things...

1. Super Native - 3.5" S110V FFG blade, no swedge like on 2009 Forum knife, low riding wire clip, midlock or ball lock, caged is fine.
2. Baby Persian - C83 bolstered reduced to Kopa size. No Boye dent, no clip. Dark green micarta scales.
3. Bolstered Caly3 with solid ZDP189 blade thinned to .010" behind the edge, 2 mm stock and smooth Giraffe bone or olive wood scales

Yojimbo 3, 3" inch blade titanium scales, deep carry titanium wire clip. Keep the deep hollow grind just slightly miniaturized.

Serrata in Cobalt... :D

I'd design a folding swick that isn't classed as an auto.

Probably a dang 5" Manix 2 XL Moonglow w/ K390 :)

Chaparral shaped knife with M4 steel compression lock 2mm blade stock and orange G10

and produced in taiwan

Second knife would be a yojimbo xl with a 3.5 blade.

Keep it S30V and G10 so I can afford one. Coat the blade.

Call it the Yojumbo.

Yojimbo 2 handle, FFG/DLC/S110V Manix 2 blade, natural linen micarta scales, deep carry wire clip.

Dream Model #1: Start with a Caly Jr., stonewashed M390 blade, no swedge, Larger Spyderhole, Jimping on thumbramp & choil, add some stategic jimping to stock gray FRN handle, keep fishscale texturing on FRN, stonewashed wire clip, or stonewashed standard clip with ENGRAVED Spyder.

Dream Model #2: Start with a Caly 3.5, stonewashed M390 blade, flush mount pivot, add Anso (or similar) macro texturing to G10 scales, provide tip down carry option.

Good Thread!

bearfacedkiller wrote:Second knife would be a yojimbo xl with a 3.5 blade.

Keep it S30V and G10 so I can afford one. Coat the blade.

Call it the Yojumbo.

Hehehe.....Cool.

bh49 wrote: 2. Baby Persian - C83 bolstered reduced to Kopa size. No Boye dent, no clip. Dark green micarta scales.
3. Bolstered Caly3 with solid ZDP189 blade thinned to .010" behind the edge, 2 mm stock and smooth Giraffe bone or olive wood scales

I'd buy either of those Roman! Very classy

Phone hickup double post.