Spyderco Forums

I do not see any 1/2 serrated delica's prior to the AUS-8 steel models. Would it be safe to say that the 1/2 serrated models did not come out until the introduction of the AUS-8 steel models? This seems to be the same with the endura's also. Will, do you have a pink and green thin clip D-1 with no blade steel marked on the blade? Take care.

tonydahose wrote:hey Will besides customs you probably have them all, you might be missing some edge type with a certain steel but i think you have the delica pretty much covered :)

yo Tony,


there are more out there somewhere I KNOW IT LOL



still looking for the blak ti Delica & i saw a FBI D2 once but its was so bad used that you could barely see the engraving.

i still look everyday for something new, cant wait to see some of the new D4 FFGs to post pics of them.

BHD, the collection isnt edge at all, just different steel types, steel stamps, handles, clips, generations, colors & customs etc etc

yes the pink and green thin clip with no steel stamp is in there somewhere, i dont think they ever made them with the fat clip, either that or i havent found them yet.

Not asking about the edges of your knives. I am trying to find out if there were any 1/2 serrated delicas or enduras with no blade steel markins or G-2 steel. It seems that the 1/2 serrated blades began with the introduction of the AUS-8 steel. Take care.

BHDKnifer wrote:Not asking about the edges of your knives. I am trying to find out if there were any 1/2 serrated delicas or enduras with no blade steel markins or G-2 steel. It seems that the 1/2 serrated blades began with the introduction of the AUS-8 steel. Take care.

yes, sofar the first combo edge Delica i have is a AUS-8 fat clip, i had to open up my Spydie bags to find that one out.

good spot, never thought about this factor.

take care too

Cool. I noticed it with my endura's, but wondered if it was the same with delica's. I often use you'r group shot's as a reference and noticed no early steel 1/2 serrated D's in you'r collection. I think it would be safe to say that the 1/2 serrated model's were introduced when the AUS-8 steel came out. Maybe Sal will chime in and confirm it. Take care.

I also noticed that when the boye dent came out 1 serration was removed from the blade on the fully serrated model's. :cool:

BHDKnifer wrote:I also noticed that when the boyd dent came out 1 serration was removed from the blade on the fully serrated model's. :cool:

man you pay attention to some close detail, i looked at the first boye dent Delica i have and compared it to the non boye dent and this seems to be not the factor with Delicas, but it does seem to be they moved the inner teeth back closer to the tang, is this a factor with Enduras with missing teeth?

on the D1s though the full serrations go to the tip or closer than these, same with the Economys and Standards, maybe they learned the lesson on those first.

btw is it boye or boyd ? ive been calling it boye for years now lol

D2 SE AUS-6

Yes my ATS-55 no boye dent has 7 sets of the smaller double serrations and my ATS-55 boye dent has 6 sets of the smaller double serrations. Both have 7 large single serrations. When the boye dent came out the endura had one less set of smaller double serrations. Take care.

I just checked my delicas. I have an ATS-55 pink D-3 no boye dent and an ATS-55 blue D-3 with a boye dent. The blue D-3 has 1 less set of small double serrations. Take care.

BHDKnifer wrote:I just checked my delicas. I have an ATS-55 pink D-3 no boye dent and an ATS-55 blue D-3 with a boye dent. The blue D-3 has 1 less set of small double serrations. Take care.

please post pics,. this is getting crazy now. and i like it

My picture quality is pretty bad, but I will get my wife to help.

BHDKnifer wrote:My picture quality is pretty bad, but I will get my wife to help.

cant be any worse than mine :D

btw way i looked at my Pink D3 with a chipped tip and you are right, but i can only base it off of a VG-10 D3 SE, the PINK is ATS-55 without the boye

i also still cant find a D3 VG-10 without a boye, maybe doesnt exist but i still look for it

I was a LeBarons yesterday and they have what I believe to be a D4 with an FFG blade, VG-10, FRN.

My little guy was having control issues so I didn't get to handle it.

Was this a D4 at all? I didn't know they came FFG PE.

FIMS wrote:I was a LeBarons yesterday and they have what I believe to be a D4 with an FFG blade, VG-10, FRN.

My little guy was having control issues so I didn't get to handle it.

Was this a D4 at all? I didn't know they came FFG PE.

sounds like seen the new D4s FRN FFG that are coming out but i havent heard anything of them being out yet ?

Here's my very first Spyderco ...Very Well Loved and Used . Take Very Good Care and Be Safe Always.

God Bless :)


-raven-

no dent on this pink d3

raven wrote:Here's my very first Spyderco ...Very Well Loved and Used . Take Very Good Care and Be Safe Always.

God Bless :)


-raven-

I have one just like that coming to me in the mail! It'll be my second Delica - I also have a D4 PE.

BWPerdue wrote:I have one just like that coming to me in the mail! It'll be my second Delica - I also have a D4 PE.

post pics please

Delica4 fully flat ground Green PE...

i must add that i really like these colors, especially the blue and green. the grey is pretty much foliage green to me.
I held them up next to each other and its super close.

i thought by not adjusting the color of the pic it would portray the true color, but after putting the knife against the picture
these pics are very dull, the colors are much more true in hand.