Show those Edges !!!!!

[chuck_roxas45]

Great edge senor. :D

Took the stones to her right proper...


Untitled by senorsquare, on Flickr

[Holland]

Awesome job senor! Was it any more difficult then the steels You've reprofiled?

[senorsquare]

Great edge senor. :D

Awesome job senor! Was it any more difficult then the steels You've reprofiled?

Thanks guys. It took a little more work than M390 or M4, but not too much. I used an Atoma 140 grit diamond plate to do bulk of the reprofile work which helped it go a little quicker.

This steel takes a wickedly sharp edge. I was getting kind of giddy push cutting phone book paper like it wasn't even there. :D

[PanChango]

Here's a pic of my Breeden Rescue. There is still a small hitch in the blade, but I didn't want to remove that much steel when the rest was sharp. It will be gone next time I use the stones.

[.357 mag]

Haven't seen any Fiskars here yet..

[MadRookie]

Oooh, that's a cool edge!

:)

Well done.

:)

[.357 mag]

Oooh, that's a cool edge!

:)

Well done.



:)

Thanks!

[senorsquare]

1000 grit EP stone.


Untitled by senorsquare, on Flickr

[Jax]

opps

[Jax]

<a href="http://www.flickr.com/photos/100154210@N02/9491918032/" title="IMG_4744[1] by jaxonbeilner, on Flickr"><img src="http://farm8.staticflickr.com/7420/9491 ... ba78af.jpg" width="500" height="375" alt="IMG_4744[1]"></a>
<a href="http://www.flickr.com/photos/100154210@N02/9489125345/" title="IMG_4759[1] by jaxonbeilner, on Flickr"><img src="http://farm8.staticflickr.com/7349/9489 ... 3e7242.jpg" width="500" height="375" alt="IMG_4759[1]"></a>

[Jax]

http://www.flickr.com/photos/100154210@N02/9491918032/
http://www.flickr.com/photos/100154210@N02/9489125345/
sorry for the two above deleted posts,having a hard time figuring out how to post the picture here..

[MadRookie]

Nice edges there.

:)

[Jax]

Thanks :)
but not quite as amazing as your Benchmade video :)

[razorsharp]

25 minute reprofile and polish job

[Clip]

I just bought another bench grinder and attached my belt attachment. To it, will likely regrind my forum native when I get it. A nice ffg to 0.008 should be good

I've got an 8" grinder begging for something. What's this belt attachment you've got? Also, love the new edge on the forum N5. Angle?

[Holland]

Very nice Travis!

[razorsharp]

I've got an 8" grinder begging for something. What's this belt attachment you've got? Also, love the new edge on the forum N5. Angle?

The belt attachment is off a China grinda, :p . The angle on the native is probably about 11 dps took 25 minutes

[Holland]

14 dps 1000 grit and stropped


14 dps 400 gritt


15 dps 400 gritt

[rg02]

Wish I had better photography skills! It really is a nice mirrored edge. 20 deg each side on the wicked edge and progressed through grits: 100,200,400,600,800,1000, 1200, 1600, and stropped with 5, 3.5, 1, and 0.5 micron paste.

[78lilred]