Do you have an Ugly Spidie?

Discuss Spyderco's products and history.
Post Reply
User avatar
noseoil
Member
Posts: 506
Joined: Sun Apr 07, 2013 5:28 pm

Do you have an Ugly Spidie?

#1

Post by noseoil »

I sent away for a project knife to do some practicing for metal finishing. It's an older Spyderco Delica Clipit in VG 10, with a bit of wear showing on the blade. I got it "used" and I must say I'm not disappointed, it's all I could ever wish for in a project knife. I'm not sure how this finish was achieved, but it looks like it may have been done with a Dremel and several quarts of strong coffee. I sent an email to the previous owner, but so far haven't heard back yet about the finish and how it was achieved.

Here are a couple of pictures showing off the fine "patina" as it arrived yesterday. I'll post more once I've done some work on it, but for now this will have to do. Don't worry, I'm putting on my nomex skivies, if you would care to comment on the finer points of this blade.

Image

Image

Image

Please feel free to post the ugliest Spydie you have, no safe queens please!
Top
User avatar
kbuzbee
Member
Posts: 4764
Joined: Sun Aug 13, 2006 8:37 am
Location: Mentor, OH

#2

Post by kbuzbee »

The only ugly thing associated with any of my Spydercos is me ;) and no amount of cleaning is gonna help that....

Ken
玉鋼
Top
Sithus1966
Member
Posts: 802
Joined: Thu Apr 01, 2010 9:49 pm
Location: Michigan

#3

Post by Sithus1966 »

I had this one.
Image

But I fixed it.
Image
C05, C05S, C10SRD, C10SBK(x2), C10FPBR, C10GRE, C10FPGR, C11, C11FPBK, C12SBK2, C14 C17 C21, C28BK, C28BK2, C28YL2, C36, C45, C54GPBN, C77, C80GPOR, C81, C81GS, C81GBK2, C85GP2, C86, C86P, C86PET, C90, C94, C95, C106, C109, C116, C122, C123CF, C123, C123GBL, C126(x2), C132GP, C135GP, C136, C137, C138, C140, C142, C146CFP, C148, C158TIP, C161GP, C162, C163PBK, C164GPBN, LBK, LBKII(x2), LYL3HB, LGRE3, MBK, FB20, FB23, FB24SBK, FB31SBK, FBPBK, MT12, MT13, MT16, Woodcraft.
Top
User avatar
The Mastiff
Member
Posts: 6059
Joined: Sun Jun 04, 2006 2:53 am
Location: raleigh nc

#4

Post by The Mastiff »

I have several I've taken sandpaper to in order to get rid of deeper scratches and or rust. I end up with a satin type finish of sorts though it doesn't look professional. It does clean ok and doesn't rust which was the purpose. I have a lot of older knives in general like that I had to de rust to get it stopped before pitting got too deep. I have never went for a really fine or mirror finish but I do enough to get the rust than even it out and quit. :) I tried a dremel once and went back to hand sanding. I used to hit up flea markets looking for old carbon steel knives when they were a little harder to find. Back in the 80's carbon steel was only used in a few lines. Fixed blades weren't as bad but folders, especially ones I could afford back then were all pretty much stainless. There wasn't any VG10, S30V, S90V, M390 etc. around either in production knives until Spyderco, then Benchmade, Microtech etc. started looking for better steels.They drove things as they still do now I recall being very impressed with G2/Gin 1 compared to the usual and I began looking around which turned into a full blown steel junky compulsion. Even thousand dollar knives (Randall etc. ) were 440 grade steel.

Joe
"A Mastiff is to a dog what a Lion is to a housecat. He stands alone and all others sink before him. His courage does not exceed temper and generosity, and in attachment he equals the kindest of his race" Cynographia Britannic 1800


"Unless you're the lead dog the view is pretty much gonna stay the same!"
Top
User avatar
kbuzbee
Member
Posts: 4764
Joined: Sun Aug 13, 2006 8:37 am
Location: Mentor, OH

#5

Post by kbuzbee »

Sithus1966 wrote:
But I fixed it.
Nice! I like what you did there!

Ken
玉鋼
Top
User avatar
ChapmanPreferred
Member
Posts: 2342
Joined: Fri Sep 24, 2004 10:33 am
Location: PA, USA
Contact:
Contact ChapmanPreferred

#6

Post by ChapmanPreferred »

Repaired User VG10 Dragonfly with a ZDP Dragonfly w/o damage.

Image

Image

Repaired tip damaged 440V CE (now looks like full SE) Military with a non damaged Military.

Image

Image

Image

A Delica II SS that came to me with only about 1" of blade left. The rest was snapped off somehow.

Image

This one has moved on to one of my co-workers who is no longer in my location.
SFO Alumni/Authorized Spyderco Dealer (Startup)
Work EDC List
FRP: Nisjin Cricket PE, Manbug PE, Dragonfly PE
FLP: SS Cricket SE, byrd Flatbyrd CE
BRP: CF Military S90V
BLP: Forum S110V Native
[SIGPIC][/SIGPIC]
Top
rodloos
Member
Posts: 1625
Joined: Sun Sep 06, 2009 9:22 pm
Location: DFW, TX

#7

Post by rodloos »

Those are some interesting repair jobs!

On another forum, I saw someone selling their Temperance with a broken tip, for $20 shipped. Maybe I should buy it to learn how to do blade rescues? :)
Which Knife, A or B? get Both! (and C, D and E) :)
Top
User avatar
kennethsime
Member
Posts: 4967
Joined: Thu Dec 29, 2011 7:28 pm
Location: California

#8

Post by kennethsime »

rodloos wrote:Those are some interesting repair jobs!

On another forum, I saw someone selling their Temperance with a broken tip, for $20 shipped. Maybe I should buy it to learn how to do blade rescues? :)
Do it, restore it, then sell it to me at the same price. It was just a learning tool, right? :p
I'm happiest with Micarta and Tool Steel.

Top four in rotation: K390 + GCM PM2, ZCarta Shaman, Crucarta PM2, K390 + GCM Straight Spine Stretch.
Top
User avatar
kennethsime
Member
Posts: 4967
Joined: Thu Dec 29, 2011 7:28 pm
Location: California

#9

Post by kennethsime »

I think I've posted this one before, but this guy has been the go-to office knife at my work for quite a number of years. Still sharpens up real well!

Image

Image
I'm happiest with Micarta and Tool Steel.

Top four in rotation: K390 + GCM PM2, ZCarta Shaman, Crucarta PM2, K390 + GCM Straight Spine Stretch.
Top
User avatar
noseoil
Member
Posts: 506
Joined: Sun Apr 07, 2013 5:28 pm

#10

Post by noseoil »

OK, been busy this morning, along with a few chores. Too hot outside now (109 & still climbing today), so I'm enjoying the AC & better working conditions inside the house. I used a drum sander for some general scratching of the worst gouges, but there are still a few showing which I won't remove completely.

Here's an intermediate shot or two of the rough sanding.
Image

The spine after a bit of sanding, it's better now.
Image

Here's a bit more, hand sanding up to 600 grit with a small, hard rubber block. I went from 180 to 600 at this point.
Image

The clip was sanded & polished, a new lanyard was made & cleaning is done, so here's the "new" knife and my next member for the EDC rotation. I did a 15 d.p.s. bevel and used the hard, fine white stone for the blade finish of the bevel, no micro-bevel at this point. I may strop the edge to bring up a polish, but it's doubtful at this point. Don't want to spoil it, after all.
Image

If you find an old knife, the steel is pretty forgiving and patient in waiting for a new owner and better times. You will be able to keep it as a user if there's a bit of time & elbow grease available. You don't need power tools, just some sand paper and a sharpener will make things right. If I do anything else over time, I'll post an image or two for fun.
Top
User avatar
Sequimite
Member
Posts: 2959
Joined: Sat Jan 03, 2009 8:19 am
Location: Sequim (skwim), WA

#11

Post by Sequimite »

This customized Scorpius is a testament to the perils of low resolution ebay photos and waiting too many years to get new glasses. Perfectly functional despite the decorative grinding, rubbery black paint and free form scale.

Image
Our reason is quite satisfied, in 999 cases out of every 1000 of us, if we can find a few arguments that will do to recite in case our credulity is criticized by someone else. Our faith is faith in someone else's faith, and in the greatest matters this is most the case.
- William James, from The Will to Believe, a guest lecture at Yale University in 1897
Top
O,just,O
Member
Posts: 945
Joined: Sat Jan 31, 2009 9:35 pm
Location: Qld. Australia.

#12

Post by O,just,O »

You win Squim.
O.
Top
User avatar
noseoil
Member
Posts: 506
Joined: Sun Apr 07, 2013 5:28 pm

#13

Post by noseoil »

Yep, I'll keep looking, but those scales are going to be hard to beat! Never seen anything quite like that before, hope you didn't overpay. ;)
Top
User avatar
Sequimite
Member
Posts: 2959
Joined: Sat Jan 03, 2009 8:19 am
Location: Sequim (skwim), WA

#14

Post by Sequimite »

I think it was in the $30 - $35 range. Apparently the other bidders could see it better than I could.

add-> Actually the blade is like new, lockup is solid and the weird scale gives a more comfortable grip. I'd use it if it weren't so ugly.
Our reason is quite satisfied, in 999 cases out of every 1000 of us, if we can find a few arguments that will do to recite in case our credulity is criticized by someone else. Our faith is faith in someone else's faith, and in the greatest matters this is most the case.
- William James, from The Will to Believe, a guest lecture at Yale University in 1897
Top
User avatar
chuck_roxas45
Member
Posts: 8797
Joined: Wed Mar 03, 2010 4:43 pm
Location: Small City, Philippines

#15

Post by chuck_roxas45 »

Excellent jobs, you guys!
Top
Sithus1966
Member
Posts: 802
Joined: Thu Apr 01, 2010 9:49 pm
Location: Michigan

#16

Post by Sithus1966 »

From this:
Image
To this:
Image
C05, C05S, C10SRD, C10SBK(x2), C10FPBR, C10GRE, C10FPGR, C11, C11FPBK, C12SBK2, C14 C17 C21, C28BK, C28BK2, C28YL2, C36, C45, C54GPBN, C77, C80GPOR, C81, C81GS, C81GBK2, C85GP2, C86, C86P, C86PET, C90, C94, C95, C106, C109, C116, C122, C123CF, C123, C123GBL, C126(x2), C132GP, C135GP, C136, C137, C138, C140, C142, C146CFP, C148, C158TIP, C161GP, C162, C163PBK, C164GPBN, LBK, LBKII(x2), LYL3HB, LGRE3, MBK, FB20, FB23, FB24SBK, FB31SBK, FBPBK, MT12, MT13, MT16, Woodcraft.
Top
User avatar
Simple Man
Member
Posts: 2036
Joined: Fri Sep 24, 2004 12:00 pm
Location: Kentucky

#17

Post by Simple Man »

Revived this rescue some time back, here is the link.
http://www.spyderco.com/forums/showthre ... ght=rescue

From this
Image
To this
Image
Romans 8:31 ....If God is for us, who can be against us? - <><

The Spyderco hole is a rotating mechanical assembly of one part.

".....tractors don't have to look like Ferraris" -Sal
Top
User avatar
Evil D
Member
Posts: 28683
Joined: Sat Jun 26, 2010 9:48 pm
Location: Northern KY

#18

Post by Evil D »

Sequimite wrote:This customized Scorpius is a testament to the perils of low resolution ebay photos and waiting too many years to get new glasses. Perfectly functional despite the decorative grinding, rubbery black paint and free form scale.

Image
I don't think I've ever felt the need to punch a knife, but if that knife had a face, I'd punch it.
~David
Top
User avatar
Holland
Member
Posts: 7579
Joined: Fri Jan 06, 2012 9:37 pm
Location: Alberta

#19

Post by Holland »

I think it is beautiful, but people tell me otherwise...
Image
-Spencer

Rotation:
Gayle Bradley 2 | Mantra 1 | Watu | Chaparral 1 | Dragonfly 2 Salt SE
Top
User avatar
Holland
Member
Posts: 7579
Joined: Fri Jan 06, 2012 9:37 pm
Location: Alberta

#20

Post by Holland »

Evil D wrote:I don't think I've ever felt the need to punch a knife, but if that knife had a face, I'd punch it.
Lol
-Spencer

Rotation:
Gayle Bradley 2 | Mantra 1 | Watu | Chaparral 1 | Dragonfly 2 Salt SE
Top
Post Reply

Return to “Spyderco General Discussion”