h1 mule
I thought Spyderco was using the mule as a testing platform for new steel trials, they already have knives that use both zdp and h1 so wouldn't those be the "mules"? I am not complaining or anything, I really like the mules and think its a great idea, just thought it was to test new steels. Like 52100 and cpm-m4 that have not been used in a production model as far as I know.
I was under the same understanding. I think the mule team knives are to give us "knife knuts" a chance to use different steels that have not been used before.GoMeR wrote:I thought Spyderco was using the mule as a testing platform for new steel trials, they already have knives that use both zdp and h1 so wouldn't those be the "mules"? I am not complaining or anything, I really like the mules and think its a great idea, just thought it was to test new steels. Like 52100 and cpm-m4 that have not been used in a production model as far as I know.
- araneae
- Member
- Posts: 5492
- Joined: Wed Aug 09, 2006 10:10 pm
- Location: A lil more south of the Erie shore, Ohio
Mules will be made where the steel is. There will also be a 9Cr18Mo (a new Chinese steel) Mule this year I believe. I am excited to see that one as it is an "experimental" new steel.
So many knives, so few pockets... :)
-Nick
Last in: N5 Magnacut
The "Spirit" of the design does not come through unless used. -Sal
-Nick
Last in: N5 Magnacut
The "Spirit" of the design does not come through unless used. -Sal
-
- Member
- Posts: 6914
- Joined: Sun Apr 09, 2006 2:16 pm
- Location: Liberal, Kansas
Since the Mule platform is a flat ground blade, flat grinds are done one side at a time, and H-1 has to be ground on both sides at once due to the work hardening properties of the material (at least on a production scale) I wouldn't hold my breath waiting on an H-1 Mule. Living a thousand miles from saltwater in a place that averages less than 12" of rainfall a year, I somehow fail to see the draw of H-1.
I don't believe in safe queens, only in pre-need replacements.
I was thinking an iwb sheath -summer carry right up against the body like that makes me think about sweat being an issueyablanowitz wrote:Since the Mule platform is a flat ground blade, flat grinds are done one side at a time, and H-1 has to be ground on both sides at once due to the work hardening properties of the material (at least on a production scale) I wouldn't hold my breath waiting on an H-1 Mule. Living a thousand miles from saltwater in a place that averages less than 12" of rainfall a year, I somehow fail to see the draw of H-1.
C.O.T.C.O. honorary member
You might be able too... it'd just get expensive. :D What about laser cutting the sides and then finishing with a belt?yablanowitz wrote:Since the Mule platform is a flat ground blade, flat grinds are done one side at a time, and H-1 has to be ground on both sides at once due to the work hardening properties of the material (at least on a production scale) I wouldn't hold my breath waiting on an H-1 Mule. Living a thousand miles from saltwater in a place that averages less than 12" of rainfall a year, I somehow fail to see the draw of H-1.
Being 1 mile from the Pacific ocean, I would buy more than one!
(On the other hand, have bought more than one M4 & S90v Mules)
But you get the idea.
H1 Mule would be great by me!
Have held off on H1 as the models in that material have not done much for me...... But a Mule? Oh yea.............
To me, Mules are about trying many steels using the same low cast platform for comparison.
(Already had S90v and M4 blades before the Mules came out)
But really like the idea!
Not sure H1 would cost more to machine than super HARD material like M4 or S90v?
Sal.......... thoughts...........
(On the other hand, have bought more than one M4 & S90v Mules)
But you get the idea.
H1 Mule would be great by me!
Have held off on H1 as the models in that material have not done much for me...... But a Mule? Oh yea.............
To me, Mules are about trying many steels using the same low cast platform for comparison.
(Already had S90v and M4 blades before the Mules came out)
But really like the idea!
Not sure H1 would cost more to machine than super HARD material like M4 or S90v?
Sal.......... thoughts...........
:spyder: :eek: :spyder: :eek: :spyder: :eek: :spyder:
More S90v & CF please.......
More S90v & CF please.......
-
- Member
- Posts: 6914
- Joined: Sun Apr 09, 2006 2:16 pm
- Location: Liberal, Kansas
I think sending 600 Mules to Tom Krein for a flat grind would get a touch expensive. Not to mention H-1 being pretty expensive stuff to begin with. How many of you are up for a $150 Mule?Josh K wrote:You might be able too... it'd just get expensive. :D What about laser cutting the sides and then finishing with a belt?
I don't believe in safe queens, only in pre-need replacements.
How expensive is H1? There isn't much (~$12) difference between a Delica and a Salt I. I guess you could write off the nested steel liners, and screw construction in the Delica's favor.yablanowitz wrote:I think sending 600 Mules to Tom Krein for a flat grind would get a touch expensive. Not to mention H-1 being pretty expensive stuff to begin with. How many of you are up for a $150 Mule?
But compared to M4 and S90V ($70) I can't imagine H1 being more expensive then that. I know the Aqua Salt's MSRP is about $180, street price is about $120.
- Sword of Morning
- Member
- Posts: 93
- Joined: Thu Jan 01, 2009 10:06 am
But also a very aesthetic and EDC friendly fixed blade without thinking on the purpose of the Mule concept. I would even buy them as a regular production model with scales in place and a good working steel like CPM S30V and VG-10. Of course we get this great knife with "super" steels like CPM S90V and M4. Who knows what's next?MCM wrote:To me, Mules are about trying many steels using the same low cast platform for comparison.
From a collector's standpoint, H-1 and ZDP-189 Mule's would be great. From a user standpoint, H-1 has already been available for some time in other knives of similar price. ZDP-189 is a little more expensive in the Endura/Delica, but still fairly affordable. CPM S90V was a good choice for a Mule because it could only be found in the highest priced Spyderco's until now.
-
- Member
- Posts: 6914
- Joined: Sun Apr 09, 2006 2:16 pm
- Location: Liberal, Kansas
When you consider the Salt 1 is a one-piece injection molded handle with just two pins for assembly, produced using the same molds as the Delica 3, (molds which have long since been paid for by producing previous models) and the D4 uses new molds (probably still being paid for), liners and more expensive screw construction, yet the D4 costs less, you should start getting an idea how expensive H-1 is.Josh K wrote:How expensive is H1? There isn't much (~$12) difference between a Delica and a Salt I. I guess you could write off the nested steel liners, and screw construction in the Delica's favor.
But compared to M4 and S90V ($70) I can't imagine H1 being more expensive then that. I know the Aqua Salt's MSRP is about $180, street price is about $120.
If you have to hand grind each blade, with the grinding of the first side causing the metal to harden to RC 65, grinding the other side is going to eat up abrasives in a hurry. That will add a lot to the cost of the knife. That's why all the H-1 knives are hollow ground, both sides are ground at the same time to avoid the work-hardening issue. Flat grinding H-1 would be like heat-treating the M-4 before it is ground and then trying to preserve the heat-treat throughout the grinding process.
I don't believe in safe queens, only in pre-need replacements.
- Sword of Morning
- Member
- Posts: 93
- Joined: Thu Jan 01, 2009 10:06 am