Caly III 100,000 Mile Stress Test

Discuss Spyderco's products and history.
User avatar
Bolster
Member
Posts: 5995
Joined: Sat Mar 03, 2007 12:27 pm
Location: CalyFRNia Desert

Caly III 100,000 Mile Stress Test

#1

Post by Bolster »

You know how the car magazines sometimes run a car for 100K miles then evaluate it? Well here is a report after a year’s hard use on a Caly III. (I’m amazed I didn’t lose it during that time.) A year ago I started an extensive refurbish of a house (almost a rebuild). At the time my Caly III was my favorite knife, and I considered laying it aside and using something else for the hard work ahead. The back bevel was a thin 12 degrees per side, with the sharpmaker putting on the edge at 15 degrees. Thought that might be too delicate.

Plus, on this forum, I read any number of comments about the Caly III being a ‘gent’s knife,’ perhaps not up to hard work, with people occasionally expressing doubt of its strength. (Never read anybody reporting Caly IIIs were easy to break, but the innuendo was always there.) So I decided a ‘torture test’ would be fun, and this is the knife that rode in my pocket to work every day. (See how the pocket of one of my work pants is shredded by pulling it in and out so many times.)

The knife was used for all the things you’d encounter rebuilding a house, including opening bags of cement, cutting drywall, carving wood, cutting down cardboard, notching plastic, cutting templates, scraping paint, taking insulation off of wire, and when clean, cutting fruit for lunch. Sometimes I'd loan it to another worker and I don't even want to know what they did with it. Sometimes I would use the butt of it to hammer on stuff (when I was too lazy to get a hammer). I did not abuse the knife by prying with it. And, I did not use it for jobs where a disposable blade was clearly called for. So in summary it got hard use, but not abuse.

Here it is over a year later. Yesterday it was coverred in white drywall powder, and would not lock open because of the amount of drywall powder in my pockets getting into the locking mechanism. Plus, it was starting to take a long time to resharpen on the sharpmaker, so today I cleaned it up, oiled it with mineral oil, and finally reprofiled it back to 12 degrees…which took less time than writing this post. A couple of swipes with the fine sharpmaker stones, and we’re back to free cutting paper.

It still locks up with authority. The black in the spyder is worn away, there are scratches on the blade, and yesterday (before reprofiling) there were a few notches in the belly of the blade. The vertical blade play is around 1mm at the tip. There is wear under the G-10 under the clip.

My conclusion is, this is a hard working knife. Call it a “gent’s knife” if you will, but it just keeps on cutting in a harsh environment. I think this real-world test of endurance should help put to rest its undeserved reputation as a potentially fragile knife. It's more of a mini-mini-Manix, in my opinion.

Hard Use Caly III...still going strong:

Image

Image

Image
Steel novice who self-identifies as a steel expert. Proud M.N.O.S.D. member 0003. Spydie Steels: 4V, 15V, 20CV, AEB-L, AUS6, Cru-Wear, HAP40, K294, K390, M4, Magnacut, S110V, S30V, S35VN, S45VN, SPY27, SRS13, T15, VG10, XHP, ZWear, ZDP189
scout
Member
Posts: 351
Joined: Fri Sep 24, 2004 10:33 am
Location: Austin, Tx.

#2

Post by scout »

Awesome review! It looks a lot better than I thought it would. :D
User avatar
wescobts
Member
Posts: 324
Joined: Mon Sep 08, 2008 5:35 pm
Location: Western New York

#3

Post by wescobts »

Excellent review, and as Scout said I'm surprised at the appearance, a good credit to Spyderco. Although I do not own one it is a great knife.
learning it the hard way... :rolleyes:
User avatar
Jazz
Member
Posts: 7678
Joined: Sun Jul 01, 2007 7:46 pm
Location: Alberta, Canada

#4

Post by Jazz »

It looks great after all that cutting! Thanks a lot for the review. I love my Caly 3's :) :cool: .

- best wishes, Jazz.
User avatar
CajunMike
Member
Posts: 143
Joined: Fri Nov 17, 2006 8:24 pm
Location: Louisiana
Contact:

#5

Post by CajunMike »

Great review! Glad to hear my Caly 3 is up to the task. :D
Cheers,
Mike
I may not have gone where I intended to go, but I think I have ended up where I needed to be.
Douglas Adams
User avatar
quattrokid73
Member
Posts: 825
Joined: Fri Nov 02, 2007 11:54 am
Contact:

#6

Post by quattrokid73 »

The Caly3 is my fav companion because of it's "jack of all trades" design. My cutting needs revolve around fine slicing and not raw blade strength, and I'd guess the same goes for most knife users also.

If only it had torx construction!!!
http://www.coroflot.com/aham73

:spyder: Orange Millie, UKPK Orange, DP UKPK, FRN UKPK Maroon DP, Urban Wharnie, Chokwe, Zulu, Mini Persian G-10, Spin Etched, Leafstorm, Caly Jr Gray, Sage 3, Lum CF

Every machine is the spiritualization of an organism.
MANIXWORLD
Member
Posts: 1144
Joined: Thu Sep 27, 2007 2:51 pm
Location: South Africa Capetown

#7

Post by MANIXWORLD »

my D4's usualy stand in for all the tough tasks,where my Caly3 G10 plainedge stand in for lots of kitchen duties,where this knife realy excells,for me. the Caly3 sails thru tough foods with ease and is a real joy to use and you feel the difference with a FFG blade's slicing abilities,the way it should be. the Caly3 has a super classey look and feel and their should be an anniversary model Caly3 framed as an artpiece,i wish...,Bladesteel solid ZDP189; engraved Titanium rounded scales,Gold Spyderbug logo on scale, and blade with Sal and Eric's signature on. just a thought...dream...
User avatar
The Deacon
Member
Posts: 25717
Joined: Fri Sep 24, 2004 10:33 am
Location: Upstate SC, USA
Contact:

#8

Post by The Deacon »

Excellent review.

Caly 3 is a very well built knife. I think when folks suggest it as being suitable for consideration as a gent's knife, they mean it is well built, well finished, somewhat handsome, and civilized enough not to be instantly categorized as a weapon by reasonable NKPs - rather than "glorified letter opener and nail cleaning tool".
Paul
My Personal Website ---- Beginners Guide to Spyderco Collecting ---- Spydiewiki
Deplorable :p
WTC # 1458 - 1504 - 1508 - Never Forget, Never Forgive!
User avatar
Peter1960
Member
Posts: 3676
Joined: Fri Nov 18, 2005 1:54 pm
Location: Austria, Europe

#9

Post by Peter1960 »

+1 ... really excellent review & comment. I'm glad the Caly3 did all the things you want(ed) to do :)
Peter - founding member of Spydiewiki.com

"Integrity is being good even if no one is watching"
Spyderco's company motto
User avatar
bh49
Member
Posts: 11466
Joined: Tue Feb 14, 2006 12:37 pm
Location: former Constitution state

#10

Post by bh49 »

Great review. Thank you for sharing.
But you broke my heart, when you said about "scraping paint". Probably I still baby my Caly3. I used it mostly for lunch, mail, occupationally boxes. Persian is getting all beating, still no scraping, only cutting. :)
Thanks again. I really enjoyed your review.
"People sleep peaceably in their beds at night only because rough men stand ready to do violence on their behalf"

My top choices Natives5, Calys, C83 Persian
choubbi
Member
Posts: 74
Joined: Mon Oct 27, 2008 8:51 am
Location: close to Paris, France

#11

Post by choubbi »

Thanks for the review!

The PE Caly III is the only calypso form factor knife I don't have that is still available, I think I'll get one when I get my Urban knives, if I have enough money.
User avatar
mrappraisit
Member
Posts: 1435
Joined: Fri Nov 16, 2007 10:28 am
Location: AZ,480

#12

Post by mrappraisit »

Nice review/test Bolstermanic! The CalyIII is great knife that is well worth the money. Looks like you put a nice edge on the knife, that must be it's reward for all that hard work. :D
After enlightenment, the laundry.
User avatar
Water Bug
Member
Posts: 2208
Joined: Sat Feb 23, 2008 10:21 pm
Location: United States of America

#13

Post by Water Bug »

For a knife that's been put through its paces, it looks pretty darn good. Thanks for sharing your review!
vivi
Member
Posts: 15781
Joined: Mon Oct 29, 2007 8:15 am

#14

Post by vivi »

The Caly 3 is a very tough knife. Even the linerless UKPK with a reprofiled edge can stand up to batoning and chopping. Spyderco makes some pretty tough knives. I don't know how many of you have tried but even the Spin can be stabbed into wood using heavy force and the lockbar doesn't even travel further to the right.
May you find peace in this life and the next.
User avatar
Spygineer
Member
Posts: 343
Joined: Tue May 08, 2007 2:40 pm

#15

Post by Spygineer »

Great review! Recession or no recession, I am determined to get me a Caly3!!!
I'm Hooked like a hawkbilll!!!:D
User avatar
mrappraisit
Member
Posts: 1435
Joined: Fri Nov 16, 2007 10:28 am
Location: AZ,480

#16

Post by mrappraisit »

Spygineer wrote:Great review! Recession or no recession, I am determined to get me a Caly3!!!
Money well spent, you won't regret it.
After enlightenment, the laundry.
User avatar
jabba359
Member
Posts: 4963
Joined: Fri Feb 10, 2006 10:07 pm
Location: Van Nuys, CA U.S.A. Earth
Contact:

#17

Post by jabba359 »

Bolstermanic wrote:You know how the car magazines sometimes run a car for 100K miles then evaluate it? Well here is a report after a year’s hard use on a Caly III.

...

Plus, on this forum, I read any number of comments about the Caly III being a ‘gent’s knife,’ perhaps not up to hard work, with people occasionally expressing doubt of its strength. (Never read anybody reporting Caly IIIs were easy to break, but the innuendo was always there.) So I decided a ‘torture test’ would be fun, and this is the knife that rode in my pocket to work every day. (See how the pocket of one of my work pants is shredded by pulling it in and out so many times.)

...

My conclusion is, this is a hard working knife. Call it a “gent’s knife” if you will, but it just keeps on cutting in a harsh environment. I think this real-world test of endurance should help put to rest its undeserved reputation as a potentially fragile knife. It's more of a mini-mini-Manix, in my opinion.
Thanks for the review. I've been EDC'ing my Delica for the past 7 years and have recently been looking for something to take it's place (there's nothing wrong with it, I just want to try out some other knives). The Caly 3 was at the top of my list, but I was a bit hesitant to get it since there seemed to be a lot of posts mentioning that it wouldn't hold up to hard use (based on speculation, not actual use). So I was glad to see that you took the time to not only put your knife to the test, but share your experiences with us. Because of your 100,000 mile stress test, I ordered one today. I can't wait to put it to use.
-Kyle

:bug-red
Latest arrivals: Lava Flow CF DLC Para2, Magnacut Mule, GITD Jester

http://www.spydiewiki.com
philthygeezer
Member
Posts: 123
Joined: Mon Mar 31, 2008 8:43 am

#18

Post by philthygeezer »

Bolstermanic wrote: My conclusion is, this is a hard working knife. Call it a “gent’s knife” if you will, but it just keeps on cutting in a harsh environment. I think this real-world test of endurance should help put to rest its undeserved reputation as a potentially fragile knife. It's more of a mini-mini-Manix, in my opinion.

Hard Use Caly III...still going strong:
philthygeezer wrote:I don't understand the perception that the Caly is less rugged than the Delica. Is is that it was called a Gentleman's knife? The Delica has a flange at the choil of the Caly 3 - does this give the impression that it's weaker? The blade widths at the pin seem very similar. Is the choil or slimmer handle fooling people?

The blade is the same thickness as the Endura and the pivot looks stronger to me. The G10 and steel liners must be at least as or more rugged than the FRN of the delica.

Personally, I get the impression that the Caly 3 is like a short Endura in strength. A step stronger than the Delica. Like a mini Mini Manix.
I called it! W00t! :D
User avatar
sixheads
Member
Posts: 310
Joined: Thu Apr 05, 2007 6:05 am

#19

Post by sixheads »

Great thread, I love my Caly 3 its my fave all time spydie and edc. I just got a sage and it awsome but its not my beloved Caly 3.

the caly 3 is the only Knife i have ever considerd buying a back up of.

Sixheads
Veegun
Member
Posts: 53
Joined: Mon Mar 17, 2008 9:37 pm

#20

Post by Veegun »

Why wouldn't the C3 hold up well?


Have you seen how thick the liners are?
Post Reply