Stretch 2 pivot screw washer size

[PlungeGrind]

Anyone know the size of the tiny washer that goes with the pivot screw on the stretch 2 k390? I seem to have lost mine somehow.
Thanks in advance!

[cjk]

The Delica, Endela, and Endura all use the same washers. I'd bet the Stretch 2 does too. There are replacements available in the aftermarket.

I'm sure Spyderco can supply a replacement, but it's an internal part, so you'd probably need to send your knife in for service. I believe their policy is that they don't send out internal parts.

[PlungeGrind]

The Delica, Endela, and Endura all use the same washers. I'd bet the Stretch 2 does too. There are replacements available in the aftermarket.

I'm sure Spyderco can supply a replacement, but it's an internal part, so you'd probably need to send your knife in for service. I believe their policy is that they don't send out internal parts.

Thanks, do you know the washer size?

[cjk]

The Delica, Endela, and Endura all use the same washers. I'd bet the Stretch 2 does too. There are replacements available in the aftermarket.

I'm sure Spyderco can supply a replacement, but it's an internal part, so you'd probably need to send your knife in for service. I believe their policy is that they don't send out internal parts.

Thanks, do you know the washer size?

not offhand, but here's where you can buy some.
https://www.knivesplus.com/replacement- ... ndela.html

iirc, there was a washer size thread on this forum.

[PlungeGrind]

The Delica, Endela, and Endura all use the same washers. I'd bet the Stretch 2 does too. There are replacements available in the aftermarket.

I'm sure Spyderco can supply a replacement, but it's an internal part, so you'd probably need to send your knife in for service. I believe their policy is that they don't send out internal parts.

Thanks, do you know the washer size?

https://www.knivesplus.com/replacement- ... ndela.html

Those are the washers for the pivot. I’m looking for the washer that goes on the pivot screw.

Have you disassembled a stretch?

[cjk]

thread about Delica washer size which I expect to be the same:
viewtopic.php?t=64451

quoted post with measurements:

Outside diameter 0.316"
Inside diameter 0.161"
Thickness 0.0035"

Stay safe,

Mike

Did you lose both? If you lost one, you could measure the other.

[PlungeGrind]

thread about Delica washer size which I expect to be the same:
viewtopic.php?t=64451

quoted post with measurements:

Outside diameter 0.316"
Inside diameter 0.161"
Thickness 0.0035"

Stay safe,

Mike

Did you lose both? If you lost one, you could measure the other.

Again I am not looking for a pivot washer, I am looking for the pivot screw washer. Do you l is what size the pivot screw washer is?

[N. Brian Huegel]

https://www.spyderco.com/service-suppor ... ty-repair/

Toll-free: 800-525-7770 X 3

customerservice@spyderco.com

Ask the source! This department was created to be of assistance.

nb

[PlungeGrind]

https://www.spyderco.com/service-suppor ... ty-repair/

Toll-free: 800-525-7770 X 3

customerservice@spyderco.com

Ask the source! This department was created to be of assistance.

nb

Yes, if they would only reply that would be great, but alas every time I email them, crickets.

Unfortunately customer service at Spyderco is becoming as subpar as BM.

[cjk]

Oh that washer! It appears to be sometimes included and sometimes not. I've had several K390 Delicas. Some of them had it and some of them didn't.

I do have a K390 Stretch 2.

I measured with a cheap set of digital calipers.
The washer is tiny. It's fairly difficult to measure, so these are approximate. I dropped it a lot while measuring. The thickness was the easiest to measure.

outer diameter (inches/mm): .224 / 5.5
inner diameter: .082 / 2.06
thickness: .013 / .32

It's the same washer as is sometimes on a Delica/Endura and sometimes not. Given that it's sometimes included and sometimes not, I wouldn't sweat too much that it's missing.
I compared the washer on my K390 Stretch 2 and the one on an old ZDP-189 Delica. They were the same as far as I could tell.

[TazKristi]

https://www.spyderco.com/service-suppor ... ty-repair/

Toll-free: 800-525-7770 X 3

customerservice@spyderco.com

Ask the source! This department was created to be of assistance.

nb

Yes, if they would only reply that would be great, but alas every time I email them, crickets.

Unfortunately customer service at Spyderco is becoming as subpar as BM.

Hi, PlungeGrind:
I checked with W&R, and they haven't received any emails from you (at least not from the email address you use on the forum). Please send me a PM with your contact information and I can have them check again.

Kristi

[PlungeGrind]

Oh that washer! It appears to be sometimes included and sometimes not. I've had several K390 Delicas. Some of them had it and some of them didn't.

I do have a K390 Stretch 2.

I measured with a cheap set of digital calipers.
The washer is tiny. It's fairly difficult to measure, so these are approximate. I dropped it a lot while measuring. The thickness was the easiest to measure.

outer diameter (inches/mm): .224 / 5.5
inner diameter: .082 / 2.06
thickness: .013 / .32

It's the same washer as is sometimes on a Delica/Endura and sometimes not. Given that it's sometimes included and sometimes not, I wouldn't sweat too much that it's missing.
I compared the washer on my K390 Stretch 2 and the one on an old ZDP-189 Delica. They were the same as far as I could tell.

Awesome! Thanks for the info, that’s exactly what I was looking for. I had several disassembled at once so maybe I didn’t lose it after all.

Thanks a million!