Need help! Dropped my Salt 2 H1 and....
Need help! Dropped my Salt 2 H1 and....
Hi everyone,
I'm new to Spyderco and the forum. My first Spyderco knife (not counting the Byrd) and current EDC is a Salt 2 with H1, I also have a PM2 with G10 in digital camo and a coming PM3 LW...I know, I'm starting to be a Spydercoholic - next in line is either the Ronin 2 or the Yojimbo 2.
Unfortunately, I dropped my Salt 2 in a bad way, it was closed but when it dropped, it somehow flipped open and started to bounce "head over heel", the tip and the blade sides hitting hard surface before stopping.
I bought a Spyderco Tri-Angle Sharpmaker, set at 40 degrees and followed the instructions on the manual. It's actually my first time to use this and I only sharpen kitchen knives with an accusharp knife and tool sharpener before or the usual sharpening stone. The end result are seen in the pics below.
I know...it looks bad, any way I can make it better, using the same Sharpmaker or the accusharp? What did I do wrong, using the sharp maker? How do I get the tip back to its original look?
I really have a lot to learn about sharpening and would appreciate your inputs. Thank you in advance. Stay safe and healthy everyone!
I'm new to Spyderco and the forum. My first Spyderco knife (not counting the Byrd) and current EDC is a Salt 2 with H1, I also have a PM2 with G10 in digital camo and a coming PM3 LW...I know, I'm starting to be a Spydercoholic - next in line is either the Ronin 2 or the Yojimbo 2.
Unfortunately, I dropped my Salt 2 in a bad way, it was closed but when it dropped, it somehow flipped open and started to bounce "head over heel", the tip and the blade sides hitting hard surface before stopping.
I bought a Spyderco Tri-Angle Sharpmaker, set at 40 degrees and followed the instructions on the manual. It's actually my first time to use this and I only sharpen kitchen knives with an accusharp knife and tool sharpener before or the usual sharpening stone. The end result are seen in the pics below.
I know...it looks bad, any way I can make it better, using the same Sharpmaker or the accusharp? What did I do wrong, using the sharp maker? How do I get the tip back to its original look?
I really have a lot to learn about sharpening and would appreciate your inputs. Thank you in advance. Stay safe and healthy everyone!
"Remember, it is never the knife's fault." - Daniel Boulud
18 Spyders and counting...
18 Spyders and counting...
- Doc Dan
- Member
- Posts: 14815
- Joined: Thu Nov 08, 2012 4:25 am
- Location: In a dimension as vast as space and as timeless as infinity.
Re: Need help! Dropped my Salt 2 H1 and....
First, get a magic marker/sharpie and color the edge so you can see where you are hitting. Second, I would personally use the 30 degree slots. H1 should be easy to work with.
I Pray Heaven to Bestow The Best of Blessing on THIS HOUSE, and on ALL that shall hereafter Inhabit it. May none but Honest and Wise Men ever rule under This Roof! (John Adams regarding the White House)
Follow the Christ, the King,
Live pure, speak true, right wrong, follow the King--
Else, wherefore born?" (Tennyson)
NRA Life Member
Spydernation 0050
Follow the Christ, the King,
Live pure, speak true, right wrong, follow the King--
Else, wherefore born?" (Tennyson)
NRA Life Member
Spydernation 0050
- VooDooChild
- Member
- Posts: 2617
- Joined: Wed Feb 21, 2018 1:29 am
Re: Need help! Dropped my Salt 2 H1 and....
Looks like a work knife, if it cuts well I wouldnt worry about how it looks.
Just practice your sharpening.
Just practice your sharpening.
"Rome's greatest contribution to mathematics was the killing of Archimedes."
Re: Need help! Dropped my Salt 2 H1 and....
Use the brown rods at 20 degrees to quickly restore the edge.
Use a technique like this to sharpen the tip if normal sharpening doesn't already fix it:
Use a technique like this to sharpen the tip if normal sharpening doesn't already fix it:
Re: Need help! Dropped my Salt 2 H1 and....
Looks like it has survived well to me. Now it's time for sharpening practice.
Re: Need help! Dropped my Salt 2 H1 and....
Hi Islandpar,
Welcome to our forum. It should clean up nicely with the sharpmaker. 30 degree to clean up and use. Some like a 40 degree micro-bevel. I just use the 30.
Think of an edge as a living thing that comes and goes, born, get's old, is reborn.
sal
Welcome to our forum. It should clean up nicely with the sharpmaker. 30 degree to clean up and use. Some like a 40 degree micro-bevel. I just use the 30.
Think of an edge as a living thing that comes and goes, born, get's old, is reborn.
sal
Re: Need help! Dropped my Salt 2 H1 and....
Hi PStone,
help yourself. We're here to share and learn.
sal
help yourself. We're here to share and learn.
sal
Re: Need help! Dropped my Salt 2 H1 and....
Plenty of great advice already, I’ll just add that in terms of aesthetics it looks like you didn’t spend enough time on one grit level to fully erase the scratch pattern from the previous one. That’s how you get that ugly splotchy pattern.
I was pretty excited to sharpen this guy last night, but low on time so I did it the same way. The edge is ugly, but it’s slicing like a beast today.
I was pretty excited to sharpen this guy last night, but low on time so I did it the same way. The edge is ugly, but it’s slicing like a beast today.
Last edited by aaronkb on Tue Jun 29, 2021 2:43 pm, edited 1 time in total.
Re: Need help! Dropped my Salt 2 H1 and....
Anyone know why my image isn’t showing? Anyway here’s the link to it:
https://ibb.co/xF4BppQ
https://ibb.co/xF4BppQ
Re: Need help! Dropped my Salt 2 H1 and....
If you are not skilled, the solution is a guided system (Lansky, KME, etc)
Look at the edge that even a clumsy like me can get ... :o :D
Look at the edge that even a clumsy like me can get ... :o :D
Si vis pacem para bellum
- bbturbodad
- Member
- Posts: 1180
- Joined: Sun Mar 24, 2019 9:18 am
Re: Need help! Dropped my Salt 2 H1 and....
Use the Full image (linked) BBcode link to embed the photo.aaronkb wrote: ↑Tue Jun 29, 2021 2:25 pmAnyone know why my image isn’t showing? Anyway here’s the link to it:
https://ibb.co/xF4BppQ
-Turbo
Re: Need help! Dropped my Salt 2 H1 and....
Ah, thank you!!bbturbodad wrote: ↑Tue Jun 29, 2021 4:41 pmUse the Full image (linked) BBcode link to embed the photo.aaronkb wrote: ↑Tue Jun 29, 2021 2:25 pmAnyone know why my image isn’t showing? Anyway here’s the link to it:
https://ibb.co/xF4BppQ
Anyway OP, it’s not the clearest picture but you can see places along the bevel where it’s reflecting light differently because there’s still some of the previous scratch pattern.
Re: Need help! Dropped my Salt 2 H1 and....
Thank you everyone! I tried Doc Dan's and Sal's advice to use the 30 deg and I've seen improvements, still much to do and learn and I once again thank everyone for their suggestions, words of wisdom and encouragement . Will continue to practice and develop sharpening skills.
Stay safe and healthy everyone
Stay safe and healthy everyone
"Remember, it is never the knife's fault." - Daniel Boulud
18 Spyders and counting...
18 Spyders and counting...
Re: Need help! Dropped my Salt 2 H1 and....
looks good!
Re: Need help! Dropped my Salt 2 H1 and....
nice work! sharpie is your buddy on these adventuresislandpar wrote: ↑Tue Jun 29, 2021 11:42 pmThank you everyone! I tried Doc Dan's and Sal's advice to use the 30 deg and I've seen improvements, still much to do and learn and I once again thank everyone for their suggestions, words of wisdom and encouragement . Will continue to practice and develop sharpening skills.
Stay safe and healthy everyone
current fav’s: K390 SS Stretch, PM2 CruWear Mircata, P.I.T.S., Subway Bowie
Re: Need help! Dropped my Salt 2 H1 and....
guess I should've kept scrolling, lol
sorry for the repeat
u.w.
sorry for the repeat
u.w.
-
- Member
- Posts: 500
- Joined: Wed Jun 17, 2020 11:57 am
- Location: Austria / Europe