Rex45=Hap40?
Rex45=Hap40?
So I was looking at the GPK page and in the product description for the manix 2 lw they put REX45 (Hitachi HAP40). I checked zknives to see if they crosslisted the two steels and they do, showing REX45 as a proprietary equivalent of HAP40.
Is this correct?
Is this correct?
Re: Rex45=Hap40?
According to Spyderco’s steel comparison chart ( https://www.spyderco.com/edge-u-cation/steel-chart/), they do seem to have very similar chemistry in terms of carbon, chromium, cobalt, molybdenum, tungsten, and vanadium. REX45 seems to have manganese, silicon, and sulfur, which are not included in HAP 40.
"We cannot live better than in seeking to become better."
--Socrates
--Socrates
Re: Rex45=Hap40?
ThanksTakuan wrote: ↑Wed Aug 26, 2020 8:29 pmAccording to Spyderco’s steel comparison chart ( https://www.spyderco.com/edge-u-cation/steel-chart/), they do seem to have very similar chemistry in terms of carbon, chromium, cobalt, molybdenum, tungsten, and vanadium. REX45 seems to have manganese, silicon, and sulfur, which are not included in HAP 40.
Re: Rex45=Hap40?
As I understand it, yes, they are analog steels. However, the Japanese hap40 steel has always been clad on spyderco knives (wrapped in a layer of another steel, SUS410), and apparently run soften than the rex45 steel on Golden-made spyderco models. It's also my understanding that the cladding makes it impossible to test the hardness of the hap40 steel inside.
- Julia
"Be excellent to each other." - Bill S. Preston, Esq.
"Be excellent to each other." - Bill S. Preston, Esq.
Re: Rex45=Hap40?
Sure thing. I’m really just biding time until Larrin can give you a proper response. :)
[Edited to account for posting delay: Julia’s response was very good. I didn’t want it to seem like I had overlooked it. :o}
"We cannot live better than in seeking to become better."
--Socrates
--Socrates
Re: Rex45=Hap40?
AFAIK, depending on where/from whom you get your data, they are either identical or nearly identical in chemical composition. In the real world from my usage/testing Rex45 is a fair bit better in terms of edge retention & toughness, the more popular theory for this difference seems to be heat treatment, I'm not entirely sure that's entirely it, but I have been super mindful of sharpening both identically as possible and I would not say Hap40 is a steel I would seek out buying more of, Rex45 on the other hand, I have pretty much every model available (not the CS Para3 dual-scale coloured models) -- HTH
Re: Rex45=Hap40?
Is there anything specific about HAP40 that makes it a no go for you? Or is it that you just find the extra performance of REX45 to be more ideal for your use? I have several knives with each and I've been very happy with both steels. I'm not the hardest knife user out there. Cut up a bunch of cardboard on garbage night or occaisionally at work, cut thick poly banding into small pieces once in awhile, maybe whittle on a hardwood block. That's about as hard use as it gets for me. So just about any steel seems to work well.JMM wrote: ↑Wed Aug 26, 2020 10:00 pmAFAIK, depending on where/from whom you get your data, they are either identical or nearly identical in chemical composition. In the real world from my usage/testing Rex45 is a fair bit better in terms of edge retention & toughness, the more popular theory for this difference seems to be heat treatment, I'm not entirely sure that's entirely it, but I have been super mindful of sharpening both identically as possible and I would not say Hap40 is a steel I would seek out buying more of, Rex45 on the other hand, I have pretty much every model available (not the CS Para3 dual-scale coloured models) -- HTH
My guess is, if we had a blade of unclad HAP40 and the same blade in REX45 and both are heat treated to same harness using the same protocols they would perform virtually identical
Of all the things I've lost I miss my mind the most!
Re: Rex45=Hap40?
JMM wrote: ↑Wed Aug 26, 2020 10:00 pmAFAIK, depending on where/from whom you get your data, they are either identical or nearly identical in chemical composition. In the real world from my usage/testing Rex45 is a fair bit better in terms of edge retention & toughness, the more popular theory for this difference seems to be heat treatment, I'm not entirely sure that's entirely it, but I have been super mindful of sharpening both identically as possible and I would not say Hap40 is a steel I would seek out buying more of, Rex45 on the other hand, I have pretty much every model available (not the CS Para3 dual-scale coloured models) -- HTH
To be clear: I am not an expert at all, have only used HAP 40 (my favorite steel so far) and never REX 45, and only "know" what I read about the latter!
Still: You think REX 45 is superior in edge retention AND toughness?! The former seems plausible, given that it is run harder as far as I know, but I don´t see why is should be tougher (there may be reasons for that I am just not aware of of course)
Anyway: Spydercos HAP 40 is great steel in my use: Very good edge retention, still fairly quick and easy to touch up, I like the cladding with SUS410 from a historical but also functional point of view (makes the blade more corrosion resistent and presumably, well, "tougher"?) and I think cladded HAP 40 looks cool and gives each knife a very individual look (differently looking Patina on the HAP 40 part and differently looking "scratch pattern" on the very soft SUS 410 on each model)
Furthermore I personally had no rust problems with HAP 40, just forming of a nice Patina, despite using especially my HAP 40 Endura all the time and in any condition.
Top three going by pocket-time (update March 24):
- EDC: Endura thin red line ffg combo edge (VG10); Wayne Goddard PE (4V), Endela SE (VG10)
-Mountains/outdoors: Pac.Salt 1 SE (H1), Salt 2 SE (LC200N), and also Wayne Goddard PE (4V)
- EDC: Endura thin red line ffg combo edge (VG10); Wayne Goddard PE (4V), Endela SE (VG10)
-Mountains/outdoors: Pac.Salt 1 SE (H1), Salt 2 SE (LC200N), and also Wayne Goddard PE (4V)
Re: Rex45=Hap40?
JMM wrote: ↑Wed Aug 26, 2020 10:00 pmAFAIK, depending on where/from whom you get your data, they are either identical or nearly identical in chemical composition. In the real world from my usage/testing Rex45 is a fair bit better in terms of edge retention & toughness, the more popular theory for this difference seems to be heat treatment, I'm not entirely sure that's entirely it, but I have been super mindful of sharpening both identically as possible and I would not say Hap40 is a steel I would seek out buying more of, Rex45 on the other hand, I have pretty much every model available (not the CS Para3 dual-scale coloured models) -- HTH
Makes me really want to try REX 45... :) Given how great HAP 40 performs in my use, but in your experience REX 45 is even better. Maybe I should try to get that Manix 2 LW in REX 45 (since I guess it would be hard to find a REX 45 Millie for a reasonable price.. :rolleyes: )
Top three going by pocket-time (update March 24):
- EDC: Endura thin red line ffg combo edge (VG10); Wayne Goddard PE (4V), Endela SE (VG10)
-Mountains/outdoors: Pac.Salt 1 SE (H1), Salt 2 SE (LC200N), and also Wayne Goddard PE (4V)
- EDC: Endura thin red line ffg combo edge (VG10); Wayne Goddard PE (4V), Endela SE (VG10)
-Mountains/outdoors: Pac.Salt 1 SE (H1), Salt 2 SE (LC200N), and also Wayne Goddard PE (4V)
Re: Rex45=Hap40?
Depends on how you define toughness. Rex45 is noticeably more resistant to edge rolling, and both are pretty difficult to chip, so rex45 is less likely to be damaged in normal use.Wartstein wrote: ↑Wed Aug 26, 2020 11:58 pmJMM wrote: ↑Wed Aug 26, 2020 10:00 pmAFAIK, depending on where/from whom you get your data, they are either identical or nearly identical in chemical composition. In the real world from my usage/testing Rex45 is a fair bit better in terms of edge retention & toughness, the more popular theory for this difference seems to be heat treatment, I'm not entirely sure that's entirely it, but I have been super mindful of sharpening both identically as possible and I would not say Hap40 is a steel I would seek out buying more of, Rex45 on the other hand, I have pretty much every model available (not the CS Para3 dual-scale coloured models) -- HTH
To be clear: I am not an expert at all, have only used HAP 40 (my favorite steel so far) and never REX 45, and only "know" what I read about the latter!
Still: You think REX 45 is superior in edge retention AND toughness?! The former seems plausible, given that it is run harder as far as I know, but I don´t see why is should be tougher (there may be reasons for that I am just not aware of of course)
Anyway: Spydercos HAP 40 is great steel in my use: Very good edge retention, still fairly quick and easy to touch up, I like the cladding with SUS410 from a historical but also functional point of view (makes the blade more corrosion resistent and presumably, well, "tougher"?) and I think cladded HAP 40 looks cool and gives each knife a very individual look (differently looking Patina on the HAP 40 part and differently looking "scratch pattern" on the very soft SUS 410 on each model)
Furthermore I personally had no rust problems with HAP 40, just forming of a nice Patina, despite using especially my HAP 40 Endura all the time and in any condition.
BRING ON THE MANIX XL SPRINTS AND EXCLUSIVES! And 10v or K390ify the Golden lineup, please.
Top 5 folders I’ve owned: Serrated Caribbean Leaf, Shaman, Manix XL, ZDP-189/CF Caly 3.5, Native LW.
Top 5 steels I’ve owned: LC200N, K390, CPM S90V, M390, CPM REX45.
Top 3 steels I want more of: M390 class, A11 class (including K390), CPM REX45.
Top 5 folders I’ve owned: Serrated Caribbean Leaf, Shaman, Manix XL, ZDP-189/CF Caly 3.5, Native LW.
Top 5 steels I’ve owned: LC200N, K390, CPM S90V, M390, CPM REX45.
Top 3 steels I want more of: M390 class, A11 class (including K390), CPM REX45.
Re: Rex45=Hap40?
Mattysc42 wrote: ↑Thu Aug 27, 2020 12:39 amThanks! But would that enhanced resistance to edge rolling not come for the price of being a tad more prone to chip? At least in "harder than "normal use""Wartstein wrote: ↑Wed Aug 26, 2020 11:58 pmDepends on how you define toughness. Rex45 is noticeably more resistant to edge rolling, and both are pretty difficult to chip, so rex45 is less likely to be damaged in normal use.JMM wrote: ↑Wed Aug 26, 2020 10:00 pm
To be clear: I am not an expert at all, have only used HAP 40 (my favorite steel so far) and never REX 45, and only "know" what I read about the latter!
Still: You think REX 45 is superior in edge retention AND toughness?! The former seems plausible, given that it is run harder as far as I know, but I don´t see why is should be tougher (there may be reasons for that I am just not aware of of course)
......
Top three going by pocket-time (update March 24):
- EDC: Endura thin red line ffg combo edge (VG10); Wayne Goddard PE (4V), Endela SE (VG10)
-Mountains/outdoors: Pac.Salt 1 SE (H1), Salt 2 SE (LC200N), and also Wayne Goddard PE (4V)
- EDC: Endura thin red line ffg combo edge (VG10); Wayne Goddard PE (4V), Endela SE (VG10)
-Mountains/outdoors: Pac.Salt 1 SE (H1), Salt 2 SE (LC200N), and also Wayne Goddard PE (4V)
Re: Rex45=Hap40?
Rex 45 is a steel that is one of the least likely to chip, and can attribute this to the higher hardness and the toughness it has. AKA edge stability. It's not ideal for users who like to pry with their knives, also because of the higher hardness. This is where the tradeoff is.
Re: Rex45=Hap40?
Thanks! :)Albatross wrote: ↑Thu Aug 27, 2020 1:15 amRex 45 is a steel that is one of the least likely to chip, and can attribute this to the higher hardness and the toughness it has. AKA edge stability. It's not ideal for users who like to pry with their knives, also because of the higher hardness. This is where the tradeoff is.
Top three going by pocket-time (update March 24):
- EDC: Endura thin red line ffg combo edge (VG10); Wayne Goddard PE (4V), Endela SE (VG10)
-Mountains/outdoors: Pac.Salt 1 SE (H1), Salt 2 SE (LC200N), and also Wayne Goddard PE (4V)
- EDC: Endura thin red line ffg combo edge (VG10); Wayne Goddard PE (4V), Endela SE (VG10)
-Mountains/outdoors: Pac.Salt 1 SE (H1), Salt 2 SE (LC200N), and also Wayne Goddard PE (4V)
Re: Rex45=Hap40?
Do it, buy it! I know you want to :DWartstein wrote: ↑Thu Aug 27, 2020 12:02 am
Makes me really want to try REX 45... :) Given how great HAP 40 performs in my use, but in your experience REX 45 is even better. Maybe I should try to get that Manix 2 LW in REX 45 (since I guess it would be hard to find a REX 45 Millie for a reasonable price.. :rolleyes: )
If you end up not liking it, I buy it from you :D
In the pocket: Chaparral FRN, Native Chief, Police 4 K390, Pacific Salt SE, Manix 2 G10 REX45
Re: Rex45=Hap40?
You know you should! Only 2 chances left for you to try it - the Manix lw or the Chief. You've been tempted since the first g10 manix came out...Wartstein wrote: ↑Thu Aug 27, 2020 12:02 amJMM wrote: ↑Wed Aug 26, 2020 10:00 pmAFAIK, depending on where/from whom you get your data, they are either identical or nearly identical in chemical composition. In the real world from my usage/testing Rex45 is a fair bit better in terms of edge retention & toughness, the more popular theory for this difference seems to be heat treatment, I'm not entirely sure that's entirely it, but I have been super mindful of sharpening both identically as possible and I would not say Hap40 is a steel I would seek out buying more of, Rex45 on the other hand, I have pretty much every model available (not the CS Para3 dual-scale coloured models) -- HTH
Makes me really want to try REX 45... :) Given how great HAP 40 performs in my use, but in your experience REX 45 is even better. Maybe I should try to get that Manix 2 LW in REX 45 (since I guess it would be hard to find a REX 45 Millie for a reasonable price.. :rolleyes: )
But seriously, you have a ton of real-world experience with hap40, and I'd really like to see how rex45 compares in your opinion. For me the tradeoff is superior edge stability for ease in sharpening. I never had issues with hap40 rolling, but I've only used it on Delicas and Dragonflies, and I don't often use those knives for more punishing outdoor jobs (like you use your Endura). So far, rex45 seems excellent in those conditions, though. I'd love to hear what you think.
- Julia
"Be excellent to each other." - Bill S. Preston, Esq.
"Be excellent to each other." - Bill S. Preston, Esq.
Re: Rex45=Hap40?
Mn and Si is in every knife steel so if they aren't listed it's just because the amounts aren't shown in the datasheet. Sulfur is usually not an intentional addition but an impurity, so some datasheets will list a maximum allowable amount.Takuan wrote: ↑Wed Aug 26, 2020 8:29 pmAccording to Spyderco’s steel comparison chart ( https://www.spyderco.com/edge-u-cation/steel-chart/), they do seem to have very similar chemistry in terms of carbon, chromium, cobalt, molybdenum, tungsten, and vanadium. REX45 seems to have manganese, silicon, and sulfur, which are not included in HAP 40.
http://www.KnifeSteelNerds.com - Steel Metallurgy topics related to knives
Re: Rex45=Hap40?
That's interesting. Is there an industry standard maximum allowance for sulfur content?Larrin wrote: ↑Thu Aug 27, 2020 8:09 amMn and Si is in every knife steel so if they aren't listed it's just because the amounts aren't shown in the datasheet. Sulfur is usually not an intentional addition but an impurity, so some datasheets will list a maximum allowable amount.Takuan wrote: ↑Wed Aug 26, 2020 8:29 pmAccording to Spyderco’s steel comparison chart ( https://www.spyderco.com/edge-u-cation/steel-chart/), they do seem to have very similar chemistry in terms of carbon, chromium, cobalt, molybdenum, tungsten, and vanadium. REX45 seems to have manganese, silicon, and sulfur, which are not included in HAP 40.
Re: Rex45=Hap40?
Thanks! So would you say the primary difference between REX 45 and HAP 40 is the heat treatment (if there are significant differences, that is)?
"We cannot live better than in seeking to become better."
--Socrates
--Socrates
Re: Rex45=Hap40?
Yes they are the same steel, a very common PM high speed steel in Europe especially. The European designation is 1.3244. It’s sold under a lot of trade names like ASP2030, S590, and Vanadis 30.
http://www.KnifeSteelNerds.com - Steel Metallurgy topics related to knives
- araneae
- Member
- Posts: 5492
- Joined: Wed Aug 09, 2006 10:10 pm
- Location: A lil more south of the Erie shore, Ohio
Re: Rex45=Hap40?
My guess would be that the goal is as low as possible. My wife is in the Aluminum industry and they always have contaminants that are in the mix, but the goal usually is as little as possible.Albatross wrote: ↑Thu Aug 27, 2020 8:19 amThat's interesting. Is there an industry standard maximum allowance for sulfur content?Larrin wrote: ↑Thu Aug 27, 2020 8:09 amMn and Si is in every knife steel so if they aren't listed it's just because the amounts aren't shown in the datasheet. Sulfur is usually not an intentional addition but an impurity, so some datasheets will list a maximum allowable amount.Takuan wrote: ↑Wed Aug 26, 2020 8:29 pmAccording to Spyderco’s steel comparison chart ( https://www.spyderco.com/edge-u-cation/steel-chart/), they do seem to have very similar chemistry in terms of carbon, chromium, cobalt, molybdenum, tungsten, and vanadium. REX45 seems to have manganese, silicon, and sulfur, which are not included in HAP 40.
So many knives, so few pockets... :)
-Nick
Last in: N5 Magnacut
The "Spirit" of the design does not come through unless used. -Sal
-Nick
Last in: N5 Magnacut
The "Spirit" of the design does not come through unless used. -Sal