All I want for Christmas...

[abbazaba]

Rc bladeworks. Might be interested.

Sharp dressed knives. Depending on market demand.

Shepherd CC. Takes forever but would do it by hand. I was his first Manix2 LW project and he came through eventually.

BOOMER52 might. I sent him my Endela for his CAD drawings and worked on a custom design.

[Sumdumguy]

I believe so. I know I've reached out to several different people on here and BladeForum, over the past few years.
No luck yet, they either don't make anything at all anymore, or they only make custom knives now.

Hear you. A lot of these guys either move on to more lucrative work or at least get selective about what they want to work on. A few get injured and have to quit. And, unfortunately, it seems quite a few of them are a lot better craftsmen than businessmen, get in way over their heads, and wind up trashing their reputations

Only asked about BOOMER52 because he still seems to be active and still making scales for at least some Spyderco nested liner models.

I'll double check with Boomer. I'm pretty sure I've tried him, but then again I've tried 20+ different outfits. So, I could be wrong.

If I can't get something hooked soon, I'll just try to make the cad file myself and go the local CNC route.

Maybe then, I'll sell them! >:)

Rc bladeworks. Might be interested.

Sharp dressed knives. Depending on market demand.

Shepherd CC. Takes forever but would do it by hand. I was his first Manix2 LW project and he came through eventually.

BOOMER52 might. I sent him my Endela for his CAD drawings and worked on a custom design.

Thanks.

I've tried the first two, but I don't know if I've tried Shepherd CC.

[SubMicron]

You can always remove the scales and dip them in some Rit Dye to change the color, permanently.

[Sumdumguy]

You can always remove the scales and dip them in some Rit Dye to change the color, permanently.

Haha, I don't think RIT dye is going do the trick. The scale job I am after is a bit more involved than just dying the stock scales.

[foofie]

I have been looking for Watu scales - similar issues.
Part of the problem - going the cnc route takes a lot of time and effort. This is only worth it for most shops if the scales will sell at high enough volume to offset the startup cost. It sounds like the Caribbean may have a rabid but small following?

I decided to make my own scales as a result - definitely a learning process. Couple attempts, nothing worth showing except as a "what not to do" tutorial...

[Sumdumguy]

Update:

I have been in touch with Cuscadi and this project might be getting some legs. It depends on how they treat me, I'm still not thrilled that I could've had these scales done two years ago...

[Doc Dan]

Try BOOMER52 on this forum (also on Bladeforums). He has a CNC machine and only does Spyderco knives, I believe. Give him a shout and see if he can help.

[Sumdumguy]

I checked with Boomer again. No dice, unfortunately.

However, I am in contact with Cuscadi. I have sent over my request and am waiting to hear back. It may take a while, because I have to send the knife over there first.

The scales will be worth the wait, if everything works out. I may get some for my Ulize, while I'm at it.

[JD Spydo]

My biggest desire for an upcoming "Christmas" gift would be for Spyderco to do a Sprint Run of the C-60 Ayoob. Oh yes in PE & SE both on that model.

Another "Christmas" idea that I think a lot of people here would like would be a Hawkbill folder with either a G-10 or Micarta handle in a really good blade steel like XHP and of course in SE.

Well I hope that "Sumdumguy" gets his Christmas wish too

[kerrcobra]

Same as every year.... A fixed blade Spyderco in M4

That sounds awesome....I like it

x3 - Count me in as well. Street Beat in M4 sounds awesome.

[Sumdumguy]

Same as every year.... A fixed blade Spyderco in M4

That sounds awesome....I like it

x3 - Count me in as well. Street Beat in M4 sounds awesome.

An M4 Street Beat, with a Micarta handle would be beyond fantastic.

Such an excellent design...