Factory edge poll

Discuss Spyderco's products and history.

Are factory edge grind lines visible on the Spyderco(s) in your pocket?

Yes, factory grind lines are visible on the edge bevel.
28
33%
No, they are completely sharpened away.
31
36%
I have multiples on me, some have them, some don't.
22
26%
Other.
4
5%
 
Total votes: 85

AccountDeletedUserRequest
Member
Posts: 6612
Joined: Mon Oct 29, 2007 8:15 am

Factory edge poll

Postby AccountDeletedUserRequest » Thu Aug 15, 2019 5:54 pm

Take any Spydercos in your pocket out. Open them up. Can you see factory edge grind lines on the bevel?

User avatar
Evil D
Member
Posts: 21152
Joined: Sat Jun 26, 2010 9:48 pm
Location: Northern KY

Re: Factory edge poll

Postby Evil D » Thu Aug 15, 2019 6:01 pm

Voted yes because in the last couple years I've gotten lazy thanks to the Sharpmaker and I just micro bevel everything until it's thick enough to reprofile. I used to take a new knife and immediately reprofile it on my Edge Pro but it has been years since I bothered. They really should call it the Lazymaker.
SHARPEN IT LIKE YOU LOVE IT, USE IT LIKE YOU HATE IT
~David

User avatar
Albatross
Member
Posts: 483
Joined: Sat Feb 09, 2019 4:13 pm

Re: Factory edge poll

Postby Albatross » Thu Aug 15, 2019 6:09 pm

No grind lines here, I always sharpen my brand new knives before use, they never come sharp enough for my liking. I don't care which manufacturer it is, if they use belts on their edges, it's never as good as a proper hand sharpening.
sal wrote:
Fri Nov 09, 2018 3:01 pm

...But in general, I'm all about high performance, Ergos, safety. That's why I've been accused of "deigning in the dark"...

sal

User avatar
steelcity16
Member
Posts: 3377
Joined: Mon Dec 11, 2017 11:34 am

Re: Factory edge poll

Postby steelcity16 » Thu Aug 15, 2019 6:13 pm

Yep, my new Emerson Dragonfly.
:spyder: CRU-CARTA THEM ALL! :spyder:

User avatar
soc_monki
Member
Posts: 381
Joined: Mon Feb 11, 2019 8:54 am

Re: Factory edge poll

Postby soc_monki » Thu Aug 15, 2019 6:17 pm

I just leave them alone. I haven't had a dull spyderco yet, and just touch them up on the sharpmaker. No problems here!
Spyderco : Resilience, Tenacious, Persistence, Manix 2 G10, Para 3 G10, Para 3 LW, Paramilitary 2,
BBS Paramilitary 2, Amalgam
Kershaw : Tone, Cryo, Cryo 2, Thermite, Atmos, Natrix 7007cf, Natrix 7008cf, Bareknuckle 7777, Bareknuckle 20cv, Concierge
Zero Tolerance : 0566CF, 0770CF, 0770GRYBW, 0562CF, 0470, 0456CF, 0095BW, 0801TI
Ontario : Rat 1
CRKT : Caligo
Civivi : Plethiros, Baklash
Cold Steel : AD10
Benchmade : 810-1401 Contego, 15080-2 Crooked River, 15080-Custom Crooked River, 560BK-1 Super Freek, 15085 Mini Crooked River, 940-2, 550-1 Griptilian, 950bk Rift
Buck : 110, Bucklite 422, 110 LT, 110 Slim Select, 112 Slim Pro
Artisan : Tradition

TkoK83Spy
Member
Posts: 3598
Joined: Mon Sep 17, 2018 5:32 pm
Location: Syracuse, NY

Re: Factory edge poll

Postby TkoK83Spy » Thu Aug 15, 2019 6:19 pm

I have enough that I rotate regularly and really don't need to reprofile, just daily touch up...for now. I have reprofiled my BBS Para 3 to 15dps and am now doing the same with my OD Green S30V PM2 as we speak...which is going much quicker than that M390!

Cut through some plastic strapping the other day and slammed the edge into a screw head that was sticking up out of the crate that I didn't notice. Rolled it pretty bad so decided screw it, let's slim it down a bit.
Currently have 20 :spyder: 's in 14 different steels.

-Rick

User avatar
anycal
Member
Posts: 1423
Joined: Wed Jan 11, 2017 12:40 pm
Location: California

Re: Factory edge poll

Postby anycal » Thu Aug 15, 2019 6:23 pm

Some are completely sharpened away, whether I reprofiled the knife, or just kept touching it up until they disappeared.

Some have partial lines. The knives have been touched up between fine and ultra-fine :spyder: stones. I can see some lines and smooth spots along the entire edge.

Handful of knives have not been used enough to be sharpened. Maybe a few passes on a strop. Not enough to put a dent into the factory edge.

If one has enough knives, there is bound to be a mix of edges.
Peter

dsvirsky
Member
Posts: 509
Joined: Fri Sep 24, 2004 10:33 am
Location: SW VA

Re: Factory edge poll

Postby dsvirsky » Thu Aug 15, 2019 6:32 pm

Endela SE in my pocket -- hasn't been used enough to warrant more than the occasional light touch up.

User avatar
Pelagic
Member
Posts: 2440
Joined: Fri Apr 27, 2018 5:49 pm
Location: East Coast/Nomadic

Re: Factory edge poll

Postby Pelagic » Thu Aug 15, 2019 6:39 pm

I answered no instinctively, but forgot I'm carrying a new pac salt.
Pancake wrote:
Wed Aug 14, 2019 10:20 pm
Are you a magician? :eek:
Nate wrote:
Thu Apr 04, 2019 4:32 pm
You're the lone wolf of truth howling into the winds of ignorance
Doeswhateveraspidercan wrote:
Sat Jun 15, 2019 9:17 pm
You are a nobody got it?

User avatar
Woodpuppy
Member
Posts: 1844
Joined: Wed Jun 27, 2018 6:38 pm
Location: Florida

Re: Factory edge poll

Postby Woodpuppy » Thu Aug 15, 2019 6:51 pm

Cruwear Millie and AEB-L urban in my pockets. The Millie is used and the edge was taken tighter than 15dps. I’ve only stropped it. I reprofiled the Urban to 15dps. It needed it.

I do still have factory grind lines on several knives. But those in frequent rotation have all been reprofiled to 15dps.
:spyder: My other blade is a Kelly Perfect :spyder:

The Meat man
Member
Posts: 3278
Joined: Wed Jan 03, 2018 8:01 pm
Location: Missouri, USA

Re: Factory edge poll

Postby The Meat man » Thu Aug 15, 2019 6:52 pm

I voted option 3 because I have the St. Nick's Lil Native in my pocket, and I haven't touched the edge yet. In sharp contradistinction, my CPM Cru-Wear Delica, which is also in my pocket, has been reprofiled and no factory edge grinds are visible.

I generally leave the factory edge alone until it begins to dull. Then I take it to my Hapstone for a full reprofile, often lowering the angle. I never put a microbevel on a factory edge.
- Connor

"You live and learn. At any rate, you live."

User avatar
Mushroom
Member
Posts: 2105
Joined: Tue Jan 06, 2015 2:45 pm
Location: Boston, Ma. U.S.A. Earth

Re: Factory edge poll

Postby Mushroom » Thu Aug 15, 2019 7:04 pm

Nothing in my pocket right now, but there's seven different Spydies in a dump tray right next to me. These knives range from years old to a few days old, so I voted some do some don't.
This is a funny thread. :D
- Nick

:spyder:

User avatar
wrdwrght
Member
Posts: 3021
Joined: Tue Mar 01, 2011 9:35 am
Location: New Hampshire

Re: Factory edge poll

Postby wrdwrght » Thu Aug 15, 2019 7:12 pm

The Police4 I’ve been carrying for the past week has no grind lines, but they may not have been pronounced in the first place.

I have not reprofiled it since getting it over a year ago, as I have been inclined to do with new S30V, ever since having a problem with chips on two factory-edges.
Marc <— a mere data-point

RECENT ARRIVAL: 10V PM2. ON RADAR: Lil’ Native slipjoint. IN DREAMS: 4V Military2 stop-lock; 52100 Shaman; Vanax Chief.

marty_bill_
Member
Posts: 158
Joined: Tue May 24, 2016 7:03 pm
Location: Wyoming

Re: Factory edge poll

Postby marty_bill_ » Thu Aug 15, 2019 7:15 pm

Well yeah every Spydie I've ever looked at I've seen the grind lines. They are usually there along with a micro bevel. Most are pretty sharp and I use them. But it's not to long until I sharpen them. I don't do micro bevels so those are removed when I sharpen. So I voted yes.

User avatar
jdw
Member
Posts: 1044
Joined: Thu Aug 25, 2016 6:10 pm
Location: Red Dirt

Re: Factory edge poll

Postby jdw » Thu Aug 15, 2019 7:23 pm

No problems here. The recent Urban aside, I believe the best edges come out of Maniago though.
Do right always. It will give you satisfaction in life.
--Wovoka

User avatar
Jazz
Member
Posts: 7590
Joined: Sun Jul 01, 2007 7:46 pm
Location: Alberta, Canada

Re: Factory edge poll

Postby Jazz » Thu Aug 15, 2019 7:30 pm

If the edge angle is around 15° when I get it, it stays until it needs sharpening.
- best wishes, Jazz.

User avatar
Sharp Guy
Member
Posts: 5203
Joined: Tue Jan 26, 2016 2:19 pm
Location: Over here!

Re: Factory edge poll

Postby Sharp Guy » Thu Aug 15, 2019 7:35 pm

Some of mine still have grind lines and some don't because I've reprofiled and polished the bevel. Why do you ask?
Of all the things I've lost I miss my mind the most!

User avatar
Bloke
Member
Posts: 4438
Joined: Fri May 13, 2016 12:43 am
Location: Sydney, Australia.

Re: Factory edge poll

Postby Bloke » Thu Aug 15, 2019 7:47 pm

Sharp Guy wrote:
Thu Aug 15, 2019 7:35 pm
Why do you ask?
Good question Pat. :cool:

There’ve been a few sly chops at members who post clean unsharpened knives of late so it’ll be interesting to see how this thread pans out. ;)
A day without laughter is a day wasted. ~ Charlie Chaplin

JuPaul
Member
Posts: 1647
Joined: Thu Jun 27, 2019 7:06 am

Re: Factory edge poll

Postby JuPaul » Thu Aug 15, 2019 7:59 pm

steelcity16 wrote:
Thu Aug 15, 2019 6:13 pm
Yep, my new Emerson Dragonfly.
Ha, same here. Carrying my emerson dragonfly today, too, for the first time although I got it when it first came out. First time I've worn pants that were sturdy enough to deploy it- I've been in quick dry shorts all summer. ;)
- Julia

"Be excellent to each other." - Bill S. Preston, Esq.

User avatar
awa54
Member
Posts: 2372
Joined: Thu Jun 18, 2015 9:54 am
Location: Vermont, USA
Contact:

Re: Factory edge poll

Postby awa54 » Thu Aug 15, 2019 9:00 pm

"other"

as in; some factory edges are good enough that I leave them unmolested until the knife needs its first serious sharpening, *then* I re-bevel, completely removing the original edge and running it right to the plunge line.
-David

still more knives than sharpening stones...


Return to “Spyderco General Discussion”

Who is online

Users browsing this forum: 40mm, Burton Knut, Chumango, Elshauno, GrandallK, Granoo Fink, Higher, hovan2yourknives, lonerider1013, Lumpy620, Majestic-12 [Bot], MSN [Bot], Mushroom, tyd450, Wartstein, yowzer and 40 guests