Spyderco Resilience!
Spyderco Resilience!
I picked this up at Walmart today. I had bought one before, but went back to Walmart for a Tenacious and exchanged it. So, I decided I’d get another one.
It had the worst edge on it I’d ever seen from Spyderco. It had high, and low spots throughout the blade. And the line from the bevel would go up and down on one side in different areas. And the same thing on the other side. The tip also had a growth on it. It was like a piece up metal left behind.
I didn’t think much of it. So I put it straight on the Wicked Edge and fixed it! It is very sharp. It’s easily twice as sharp, as a sharp knife. It’s sharper than my PM2 Blurple S110V lol.
I sharpened it at 15DPS, then micro beveled at 18.5 DPS. And I stropped at 17.5DPS with firm pressure with 14 micron very fast like, then moved to 10 micron.
I use thick leather shoe laces to test my edge during sharpening. This works well because I can test each exact area for perfect sharpness. The heel, and mostly the very tip of the edge. It took forever to get the very tip effortlessly popping through leather shoe lace, as I had to grind a metal lump from it before I could begin sharpening. These leather shoe laces are about 85” long. And cutting just a small piece off each time to test the edge works well, and it last forever too.
It took about 1.5 hours to get it where I wanted it. But it’s fantastic now.
It had the worst edge on it I’d ever seen from Spyderco. It had high, and low spots throughout the blade. And the line from the bevel would go up and down on one side in different areas. And the same thing on the other side. The tip also had a growth on it. It was like a piece up metal left behind.
I didn’t think much of it. So I put it straight on the Wicked Edge and fixed it! It is very sharp. It’s easily twice as sharp, as a sharp knife. It’s sharper than my PM2 Blurple S110V lol.
I sharpened it at 15DPS, then micro beveled at 18.5 DPS. And I stropped at 17.5DPS with firm pressure with 14 micron very fast like, then moved to 10 micron.
I use thick leather shoe laces to test my edge during sharpening. This works well because I can test each exact area for perfect sharpness. The heel, and mostly the very tip of the edge. It took forever to get the very tip effortlessly popping through leather shoe lace, as I had to grind a metal lump from it before I could begin sharpening. These leather shoe laces are about 85” long. And cutting just a small piece off each time to test the edge works well, and it last forever too.
It took about 1.5 hours to get it where I wanted it. But it’s fantastic now.
“My daily razor blade”
Microtech Stitch CTS-204P stonewashed blade
Microtech Dirac Delta CTS-204P Black DLC
^Wicked Edge guided system^
Microtech Stitch CTS-204P stonewashed blade
Microtech Dirac Delta CTS-204P Black DLC
^Wicked Edge guided system^
Re: Spyderco Resilience!
I've been able to get Spyderco's 8cr13mov screaming sharp. I just can't make it hold the edge long enough to make me happy.
I've actually been wondering if it would be a good kitchen steel (where I can resharpen more or less at will) because it's so quick and easy to get it so sharp.
I've actually been wondering if it would be a good kitchen steel (where I can resharpen more or less at will) because it's so quick and easy to get it so sharp.
Re: Spyderco Resilience!
the resilience is great. enjoy it. i fine spyderco’s 8cr13mov to be better than that of other makers and i love my resilience even though it doesn’t see as much pocket time these days.
keep your knife sharp and your focus sharper.
current collection:
C36MCW2, C258YL, C253GBBK, C258GFBL, C101GBBK2, C11GYW, C11FWNB20CV, C101GBN15V2, C101GODFDE2, C60GGY, C149G, C189, C101GBN2, MT35, C211TI, C242CF, C217GSSF, C101BN2, C85G2, C91BBK, C142G, C122GBBK, LBK, LYL3HB, C193, C28YL2, C11ZPGYD, C41YL5, C252G, C130G, PLKIT1
spyderco steels:
H2, CPM 20CV, CPM 15V, CTS 204P, CPM CRUWEAR, CPM S30V, N690Co, M390, CPM MagnaCut, LC200N, CTS XHP, H1, 8Cr13MoV, GIN-1, CTS BD1, VG-10, VG-10/Damascus, 440C
current collection:
C36MCW2, C258YL, C253GBBK, C258GFBL, C101GBBK2, C11GYW, C11FWNB20CV, C101GBN15V2, C101GODFDE2, C60GGY, C149G, C189, C101GBN2, MT35, C211TI, C242CF, C217GSSF, C101BN2, C85G2, C91BBK, C142G, C122GBBK, LBK, LYL3HB, C193, C28YL2, C11ZPGYD, C41YL5, C252G, C130G, PLKIT1
spyderco steels:
H2, CPM 20CV, CPM 15V, CTS 204P, CPM CRUWEAR, CPM S30V, N690Co, M390, CPM MagnaCut, LC200N, CTS XHP, H1, 8Cr13MoV, GIN-1, CTS BD1, VG-10, VG-10/Damascus, 440C
- Tucson Tom
- Member
- Posts: 1633
- Joined: Tue Mar 28, 2017 10:19 pm
- Location: Somewhere in Arizona
Re: Spyderco Resilience!
The resilience is a nice little knife. I prefer the size of it's bigger brother the Tenacious, so I gave the one I had to a friend, and he loves it -- for him it was a significant upgrade from any knife he had previously owned. He is now scheming on buying a PM2 one of these days, since he gets to play with my knives. My tenacious doesn't see as much pocket time as it used to, since it has to wait its turn in line with my other knives, but I have a lot of respect for it, even though I now have much nicer knives. A good knife to carry when there is some significant chance of losing it, since your heart won't be completely broken.
Re: Spyderco Resilience!
the resilience is the bigger brother to the tenacious. it’s a big blade and it’s magnificent.Tucson Tom wrote: ↑Sat Oct 27, 2018 10:44 pmThe resilience is a nice little knife. I prefer the size of it's bigger brother the Tenacious, so I gave the one I had to a friend, and he loves it -- for him it was a significant upgrade from any knife he had previously owned. He is now scheming on buying a PM2 one of these days, since he gets to play with my knives. My tenacious doesn't see as much pocket time as it used to, since it has to wait its turn in line with my other knives, but I have a lot of respect for it, even though I now have much nicer knives. A good knife to carry when there is some significant chance of losing it, since your heart won't be completely broken.
keep your knife sharp and your focus sharper.
current collection:
C36MCW2, C258YL, C253GBBK, C258GFBL, C101GBBK2, C11GYW, C11FWNB20CV, C101GBN15V2, C101GODFDE2, C60GGY, C149G, C189, C101GBN2, MT35, C211TI, C242CF, C217GSSF, C101BN2, C85G2, C91BBK, C142G, C122GBBK, LBK, LYL3HB, C193, C28YL2, C11ZPGYD, C41YL5, C252G, C130G, PLKIT1
spyderco steels:
H2, CPM 20CV, CPM 15V, CTS 204P, CPM CRUWEAR, CPM S30V, N690Co, M390, CPM MagnaCut, LC200N, CTS XHP, H1, 8Cr13MoV, GIN-1, CTS BD1, VG-10, VG-10/Damascus, 440C
current collection:
C36MCW2, C258YL, C253GBBK, C258GFBL, C101GBBK2, C11GYW, C11FWNB20CV, C101GBN15V2, C101GODFDE2, C60GGY, C149G, C189, C101GBN2, MT35, C211TI, C242CF, C217GSSF, C101BN2, C85G2, C91BBK, C142G, C122GBBK, LBK, LYL3HB, C193, C28YL2, C11ZPGYD, C41YL5, C252G, C130G, PLKIT1
spyderco steels:
H2, CPM 20CV, CPM 15V, CTS 204P, CPM CRUWEAR, CPM S30V, N690Co, M390, CPM MagnaCut, LC200N, CTS XHP, H1, 8Cr13MoV, GIN-1, CTS BD1, VG-10, VG-10/Damascus, 440C
-
- Member
- Posts: 647
- Joined: Tue May 08, 2018 10:04 pm
Re: Spyderco Resilience!
I assume you're thinking of the Persistence?
- cabfrank
- Member
- Posts: 2926
- Joined: Sun May 08, 2011 9:07 pm
- Location: Northern California, USA, Earth
Re: Spyderco Resilience!
Yeah, it's big, similar in size to a Military. Great value.
Re: Spyderco Resilience!
Im new to sharpening. And I had to reshape the blade, and edge while maintaining a nice look, so I’m figuring it out as I go lol. It takes a little work to get rid of all the 200 grit scratches too. Plus, I go through several different stages of diamonds. Then Strop with different compounds. And I’ve gotta clean the edge in between switching compounds, grits.
Etc.etc.
Probably the sharpest edge I’ve ever put on any knife. To bad 8cr13mov scary sharp is a short lived experience.
Normally it doesn’t take long, but I wanted it pretty looking! All of this work and it’ll stay very sharp for a couple hours if that tomorrow at work haha! My PM2 S110V is still decently shaving sharp and maintains that for about 2 days. And my cutting is constant at work.
“My daily razor blade”
Microtech Stitch CTS-204P stonewashed blade
Microtech Dirac Delta CTS-204P Black DLC
^Wicked Edge guided system^
Microtech Stitch CTS-204P stonewashed blade
Microtech Dirac Delta CTS-204P Black DLC
^Wicked Edge guided system^
Re: Spyderco Resilience!
:confused: :confused:
That's hardly a 5 minute job, even including all the light passes for burr minimization. I love my DMT XX coarse!
Re: Spyderco Resilience!
Maybe I'm just getting snobby and spoiled from all the fantastic models Spyderco puts out, but I personally would have saved the $40 or whatever this Walmart knife cost and put it towards something else, or one of the many soon to be released knives.
15 's in 10 different steels
1 - Bradford Guardian 3 / Vanadis 4E Wharnie
1 - Monterey Bay Knives Slayback Flipper / ZDP 189
1 - CRK Small Sebenza 31/Macassar Ebony Inlays
1 - CRK Large Inkosi Insingo/ Black Micarta Inlays
1 - CRK Small Sebenza 31 Insingo/Magnacut
-Rick
1 - Bradford Guardian 3 / Vanadis 4E Wharnie
1 - Monterey Bay Knives Slayback Flipper / ZDP 189
1 - CRK Small Sebenza 31/Macassar Ebony Inlays
1 - CRK Large Inkosi Insingo/ Black Micarta Inlays
1 - CRK Small Sebenza 31 Insingo/Magnacut
-Rick
Re: Spyderco Resilience!
I enjoy your enthusiasm! Keep the progress reports coming.
Re: Spyderco Resilience!
there’s something great about carrying a $50 knife that is a great value and still a great tool. nothing wrong with that just because it can be found at walmart.
keep your knife sharp and your focus sharper.
current collection:
C36MCW2, C258YL, C253GBBK, C258GFBL, C101GBBK2, C11GYW, C11FWNB20CV, C101GBN15V2, C101GODFDE2, C60GGY, C149G, C189, C101GBN2, MT35, C211TI, C242CF, C217GSSF, C101BN2, C85G2, C91BBK, C142G, C122GBBK, LBK, LYL3HB, C193, C28YL2, C11ZPGYD, C41YL5, C252G, C130G, PLKIT1
spyderco steels:
H2, CPM 20CV, CPM 15V, CTS 204P, CPM CRUWEAR, CPM S30V, N690Co, M390, CPM MagnaCut, LC200N, CTS XHP, H1, 8Cr13MoV, GIN-1, CTS BD1, VG-10, VG-10/Damascus, 440C
current collection:
C36MCW2, C258YL, C253GBBK, C258GFBL, C101GBBK2, C11GYW, C11FWNB20CV, C101GBN15V2, C101GODFDE2, C60GGY, C149G, C189, C101GBN2, MT35, C211TI, C242CF, C217GSSF, C101BN2, C85G2, C91BBK, C142G, C122GBBK, LBK, LYL3HB, C193, C28YL2, C11ZPGYD, C41YL5, C252G, C130G, PLKIT1
spyderco steels:
H2, CPM 20CV, CPM 15V, CTS 204P, CPM CRUWEAR, CPM S30V, N690Co, M390, CPM MagnaCut, LC200N, CTS XHP, H1, 8Cr13MoV, GIN-1, CTS BD1, VG-10, VG-10/Damascus, 440C
Re: Spyderco Resilience!
If you're just taking the edge angle down, you're right. 8Cr grinds very fast on diamonds. If you're progressing up to a high polish, that adds the extra 15 minutes.
Personally I like a low grit back bevel and if I'm polishing anything it's the microbevel. Same performance at the apex, less time wasted.
Re: Spyderco Resilience!
I'm the same way when I microbevel.Vivi wrote: ↑Sun Oct 28, 2018 7:23 pmIf you're just taking the edge angle down, you're right. 8Cr grinds very fast on diamonds. If you're progressing up to a high polish, that adds the extra 15 minutes.
Personally I like a low grit back bevel and if I'm polishing anything it's the microbevel. Same performance at the apex, less time wasted.
Re: Spyderco Resilience!
I think the Resilience is a great knife, sort of like a poor man's Military (without the choil). I have 2 of them, one I bought and one I won in one of Spyderco's drawings. Good for kitchen duties when camping.
I wish the Walmarts in my area carried Spydercos.
I wish the Walmarts in my area carried Spydercos.
Which Knife, A or B? get Both! (and C, D and E) :)
-
- Member
- Posts: 1158
- Joined: Tue Jan 30, 2018 1:00 pm
- Location: Central Mn
Re: Spyderco Resilience!
You can order them through their site for in store pickup. So long as you don't use a 3rd party vendor you can return them in store if something is off with it.rodloos wrote: ↑Mon Oct 29, 2018 10:28 amI think the Resilience is a great knife, sort of like a poor man's Military (without the choil). I have 2 of them, one I bought and one I won in one of Spyderco's drawings. Good for kitchen duties when camping.
I wish the Walmarts in my area carried Spydercos.
I can do all things through Christ who strengthens me. Philippians 4:13
Adam
Adam
Re: Spyderco Resilience!
this is really where the resilience excels in my mind. people kind of freak when they see it, but it looks like a kitchen knife to me and it’s great when i need to cut food up for my kids and don’t want to get what i’m cutting all in the pivot. cutting a large slice of pizza in half for my kids to share is much nicer with a resilience than with even my manix lw, which i can’t take apart to clean if i need to. don’t get me wrong, i generally prefer the manix overall, but not for this specific task.
keep your knife sharp and your focus sharper.
current collection:
C36MCW2, C258YL, C253GBBK, C258GFBL, C101GBBK2, C11GYW, C11FWNB20CV, C101GBN15V2, C101GODFDE2, C60GGY, C149G, C189, C101GBN2, MT35, C211TI, C242CF, C217GSSF, C101BN2, C85G2, C91BBK, C142G, C122GBBK, LBK, LYL3HB, C193, C28YL2, C11ZPGYD, C41YL5, C252G, C130G, PLKIT1
spyderco steels:
H2, CPM 20CV, CPM 15V, CTS 204P, CPM CRUWEAR, CPM S30V, N690Co, M390, CPM MagnaCut, LC200N, CTS XHP, H1, 8Cr13MoV, GIN-1, CTS BD1, VG-10, VG-10/Damascus, 440C
current collection:
C36MCW2, C258YL, C253GBBK, C258GFBL, C101GBBK2, C11GYW, C11FWNB20CV, C101GBN15V2, C101GODFDE2, C60GGY, C149G, C189, C101GBN2, MT35, C211TI, C242CF, C217GSSF, C101BN2, C85G2, C91BBK, C142G, C122GBBK, LBK, LYL3HB, C193, C28YL2, C11ZPGYD, C41YL5, C252G, C130G, PLKIT1
spyderco steels:
H2, CPM 20CV, CPM 15V, CTS 204P, CPM CRUWEAR, CPM S30V, N690Co, M390, CPM MagnaCut, LC200N, CTS XHP, H1, 8Cr13MoV, GIN-1, CTS BD1, VG-10, VG-10/Damascus, 440C