Spyderco Lil' Nilakka Flash Batch C221GPWH Dropping

[ABX2011]

Only 1200? They'll be around for awhile.

[blueblur]

I wasn't planning on getting one but it was available and I starting thinking about it and that usually doesn't end up well for my wallet. Plus, it's in a handle color I don't have, a model I don't have and a steel I don't have, so why not?!? Hoping it's a zero grind since I'm not planning on putting it through any tough use.

[dplafoll]

//forum.spyderco.com/viewto ... =2&t=74685

[spydieh0le]

I couldn't help myself..

[yablanowitz]

I've ordered one, but not received a ship notice. They said it was in stock at the time, but who knows? If it comes, I'll check the edge thickness and post it up. And if it comes, it will likely end up in my whittling kit with my Wolfspyder (and about 20 other knives).

[abbazaba]

Mine should be here tomorrow.

[yablanowitz]

Mine arrived this morning. The blade measures 0.009" thick at the back of the edge bevel. Not bad at all, I'll soon see how it does on wood. The blade should be good, but the handle is almost too short for my hands.

[gunmike1]

Mine arrived this morning. The blade measures 0.009" thick at the back of the edge bevel. Not bad at all, I'll soon see how it does on wood. The blade should be good, but the handle is almost too short for my hands.

Thanks for measuring, that is excellent for a factory knife. Thinnest I've ever got was my Caly 3 which was somewhere around .010". Most others are in the .020" plus range.

[captnvegtble]

the handle is almost too short for my hands.

Looks like a great little knife, but this is why I haven't bought one. I don't like knives where you can't get a full four-finger grip.

[yablanowitz]

I can live with three finger grip, but two finger is pretty much unusable for me. This one is exactly the length of my right index finger, which I've found to be the minimum length I can stand to use for anything more taxing than opening an envelope.

[425KRS]

Mine arrived this morning. The blade measures 0.009" thick at the back of the edge bevel. Not bad at all, I'll soon see how it does on wood. The blade should be good, but the handle is almost too short for my hands.

Thanks for measuring, that is excellent for a factory knife. Thinnest I've ever got was my Caly 3 which was somewhere around .010". Most others are in the .020" plus range.

You gonna get one?

[brancron]

It was love at first sight!

[this_is_nascar]

Not sure if I care for the look.

[Bile Bob]

Looks like it's still in stock in a couple places, but I don't imagine it will be for long. I believe they only made 1,200 of them. Get it while you can!

30 showing in stock @ National Knives.

[gunmike1]

Mine arrived this morning. The blade measures 0.009" thick at the back of the edge bevel. Not bad at all, I'll soon see how it does on wood. The blade should be good, but the handle is almost too short for my hands.

Thanks for measuring, that is excellent for a factory knife. Thinnest I've ever got was my Caly 3 which was somewhere around .010". Most others are in the .020" plus range.

You gonna get one?

I might. Never used RWL34, and I like thin. I better make up my mind fast though.

[Molle Ninja]

It was love at first sight!

Nice pics. Glad I ordered one.

[Sherman]

Lil' Nilakka, they're really cute! Got one from ACMA in Germany after pre-order

[Cujobob]

I purchased one. It's a nice little knife, it's similar in many ways to the Des Horn model but with a few improvements. RWL 34 makes a lot more sense than S30V.

[017]

.

[GoldenSpydie]

double post