Page 154 of 155

Re: Show your mods!

Posted: Fri Apr 17, 2020 4:44 am
by Woodpuppy
Nice work! There’s a lot to like about that design.

Re: Show your mods!

Posted: Thu Apr 23, 2020 7:00 pm
by Jazz
Modded a regular Endura. Blade is same length as Endela. I think the Endela would be a fine candidate for a wharnie blade. Not quite this shape though, but it’s what I had to work with.

Image

Re: Show your mods!

Posted: Fri Apr 24, 2020 9:13 pm
by bearrowland
Nice job Jazz! I'm a big Wharnie fan.

Re: Show your mods!

Posted: Thu Apr 30, 2020 7:07 pm
by BOOMER52
Image
Image
Image

Re: Show your mods!

Posted: Thu Apr 30, 2020 8:04 pm
by bearrowland
Looks great Boomer!

Re: Show your mods!

Posted: Wed May 06, 2020 2:21 pm
by BOOMER52
Spyderco Delica/Mini Street Fighter 3... black peel ply G10 w/royal blue G10 liners...

Image
Image
Image
Image
Image
Image
Image
Image
Image

Re: Show your mods!

Posted: Wed May 06, 2020 4:55 pm
by bearrowland
👍👍

Re: Show your mods!

Posted: Thu May 07, 2020 3:03 pm
by spyderg
Been wanting to do this mod for a while now. Finally got around to it this Previously I had rounded the edges of the scales a little, acid stonewashed the clip and made a “mini choil” if you will, as I tend to use it as a utility knife with some fine cutting tasks where I like to pinch the blade with my index and thumb near the tip and have my middle finger up real close to that cutting edge.
5148C36B-6F2A-4FFE-A001-19E7F6FA4709.jpeg

Re: Show your mods!

Posted: Fri May 08, 2020 1:56 pm
by SpyderCuse
Jazz wrote:
Thu Apr 23, 2020 7:00 pm
Modded a regular Endura. Blade is same length as Endela. I think the Endela would be a fine candidate for a wharnie blade. Not quite this shape though, but it’s what I had to work with.

Image
Jazz how did you do that mod?

Re: Show your mods!

Posted: Fri May 08, 2020 4:58 pm
by Jazz
SpyderCuse wrote:
Fri May 08, 2020 1:56 pm
Jazz how did you do that mod?

I used a Dremel tool with a reinforced cut off wheel, diamond bits, a sanding bit, and a diamond disk for the top. Dipped in water to not ruin the heat treat. For the edge, I cut some with the reinforced wheel, diamond bits, and diamond disk. Various sandpapers and a strop for polishing the spine. Sharpened and made sure the edge was straight, and there you have it.

Re: Show your mods!

Posted: Fri May 08, 2020 4:59 pm
by Jazz
spyderg wrote:
Thu May 07, 2020 3:03 pm
Been wanting to do this mod for a while now...

Nice job.

Re: Show your mods!

Posted: Fri May 08, 2020 8:12 pm
by SpyderCuse
Jazz wrote:
Fri May 08, 2020 4:58 pm
SpyderCuse wrote:
Fri May 08, 2020 1:56 pm
Jazz how did you do that mod?

I used a Dremel tool with a reinforced cut off wheel, diamond bits, a sanding bit, and a diamond disk for the top. Dipped in water to not ruin the heat treat. For the edge, I cut some with the reinforced wheel, diamond bits, and diamond disk. Various sandpapers and a strop for polishing the spine. Sharpened and made sure the edge was straight, and there you have it.
Awesome thanks!

Re: Show your mods!

Posted: Thu May 21, 2020 9:54 am
by JustinB
Just got done putting some micarta on the Jazzlica :D

Image

Re: Show your mods!

Posted: Fri May 22, 2020 10:23 am
by Haunted House
Justin that’s awesome!

Re: Show your mods!

Posted: Fri May 22, 2020 11:22 am
by bearrowland
I agree!

Re: Show your mods!

Posted: Fri May 22, 2020 12:27 pm
by JustinB
Thanks guys! Hopefully it'll be enough to tie me over until the K390 wharnie is revealed ;)

Re: Show your mods!

Posted: Sat May 23, 2020 1:01 am
by kirilpetkov
Image

Image

Image

Image

Re: Show your mods!

Posted: Fri May 29, 2020 9:07 am
by z4vdBt
Endura straight spine mod by Razor Edge Knives. First pic is kind of a before and after type deal.

Image

Image

Re: Show your mods!

Posted: Mon Jun 01, 2020 4:11 pm
by willc
BA7C25C5-E35F-4047-BEE7-CA4A9A985E03.jpeg
I half switched scales on my Rex45 and S35VN Native 5’s.
Now they have a Halloween/ Philadelphia Flyers look.

Re: Show your mods!

Posted: Mon Jun 01, 2020 7:54 pm
by Maxemetman
Very very crude and first mod. Testing my more budget friendlies first. Was straightening the spine on the tenacious but ran out of time. Also added a finger choil. The indent on the G10 is just a test for texturing. More to come. After work tomorrow.