Slipjoint mod Para 3

[FK]

DiRk,

Very creative design modification, thanks for sharing.

Regards,
FK

[diRk_262]

Sal, are you still interested to get the file to 3D print the part for testing? If yes I need an E-Mail address where I can send it to.

Thanks all for your feedback.
This part produced by spyderco would be great!

[diRk_262]

Really sad that there is no answer about the part
I thought this could be a really great opportunity for Spyderco to sell more of there wonderful knives even in country’s where the knife law is prohibiting to carry a folding - locking knife.

[Wartstein]

Really sad that there is no answer about the part
I thought this could be a really great opportunity for Spyderco to sell more of there wonderful knives even in country’s where the knife law is prohibiting to carry a folding - locking knife.

So you got no reply at all where to send the part or a 3D file? You were asked to do so, right?

[Spydergirl88]

Really sad that there is no answer about the part
I thought this could be a really great opportunity for Spyderco to sell more of there wonderful knives even in country’s where the knife law is prohibiting to carry a folding - locking knife.

Did you try clicking on Sal's profile where it says "send email"?

[diRk_262]

Yes, no reply where to send the 3D model

[Woodpuppy]

*deleted*

Because Sal provided his current email below.

[Doc Dan]

Or you can contact Tazkristi, or other Spyderco employee, here and get his email since he asked you to email the file.

[Mushroom]

Yes, no reply where to send the 3D model

Follow this link to send an email to Sal - memberlist.php?mode=email&u=21

or

Mail a physical copy to the address provided on the first page.

Hi DiRk,

Welcome to our forum.

Very interesting conversion. Could I get you to send one to me?

Spyderco
Attn: Sal Glesser
820 Spyderco Way
Golden, CO 80403 USA

sal

[sal]

Sal, are you still interested to get the file to 3D print the part for testing? If yes I need an E-Mail address where I can send it to.

Thanks all for your feedback.
This part produced by spyderco would be great!

Hi DiRk,

sglesser@spyderco.com

sal

[diRk_262]

Sal, are you still interested to get the file to 3D print the part for testing? If yes I need an E-Mail address where I can send it to.

Thanks all for your feedback.
This part produced by spyderco would be great!

Hi DiRk,

sglesser@spyderco.com

sal

Thanks for your reply.
An email was send some minutes ago.

Really curious what you and Spyderco can make out of this idea.

[diRk_262]

Hi there...
Any progress or news about the part?

[Ruudr]

I am also curious how this will will play out. A very inventive idea with a lot of potential! Maibe a Lionsteel T.R.E-ish mod?

[diRk_262]

No updates on this?

[Marulaghost]

I'd imagine they're going through some prototyping and testing. That can usually take a fair while

[diRk_262]

I'd imagine they're going through some prototyping and testing. That can usually take a fair while

I would be totally ok with that. It would just be nice to hear the actual status

[rwasham]

Very interesting design....have you done anything similar for liner lock designs? I'm guessing the technology would not be terribly different. In any case, awesome!

[diRk_262]

Until now I only modded the compression lock.
Maybe the liner lock will follow

[Mushroom]

Very interesting design....have you done anything similar for liner lock designs? I'm guessing the technology would not be terribly different. In any case, awesome!

I don't think a mod like this is possible on a liner lock. This mod fits into a cutout for the compression lock that doesn't exist on a liner lock. The compression lock is not simply a liner lock on the back of the knife, it operates very differently compared to a liner lock.

[sal]

Hi DiRk,

I was checking with R&D and they said that the file did not come through and was not usable. Sorry i didn't check sooner. We'll have to do a better job. Can I get you to resend the file?

Send to:

Sglesser@spyderco.com and to
Peterj@spyderco.com

or send a disc or?

sal