Just wanted to do an update on my experience with V-toku2. On the thread "V-toku2 Love" someone was mentioning how they had issues with their V-toku2 model. Not to mention some folks not getting a good over all performance with the steel. Heres a link to my latest video on the steel after being resharpened and a little boost with a 13dps edge
https://youtu.be/tY-h2zds8xw
V-toku2 observation and update
V-toku2 observation and update
Every Steel Has Its Appeal :cool:
A.S.O.K.A Edge on Youtube
A.S.O.K.A Edge on Youtube
Re: V-toku2 observation and update
Gotta love the little-big D'fly!
I was the one with an Endura that was having terrible wire edging for the first two sharpenings (which I didn't realize the first time 'round, but resolved on the second go) and 1 to 2mm sections of the edge fracturing out with normal cutting tasks.
It seems like mine must have had either an inadequate relief stage in the HT, or more likely got overheated when the factory edge was applied, because I used it for yard work today, which included cutting hardwood and some cardboard breakdown and the edge held up perfectly.
Turns out that third time was the charm and with enough stock removal from the edge I got down to the "good stuff"... this third sharpening went deep of necessity (had to get rid of those big chips) and seems to have finally removed all of the flawed edge steel, I didn't really have any wire edge to speak of either and got a clean apex with ease (same stone progression and just a slightly higher angle than before: 15 DPS, no micro bevel, whereas the first two attempts were at 12.5 DPS).
This behavior is exactly what I'd expect from a craft made Japanese woodworking tool or traditional pattern knife, but not a machine made kiln/salt bath HT'd blade from Sakai... but all's well that ends well, now I have a solution if my V-Toku2 Delica shows the same tendencies!
I was the one with an Endura that was having terrible wire edging for the first two sharpenings (which I didn't realize the first time 'round, but resolved on the second go) and 1 to 2mm sections of the edge fracturing out with normal cutting tasks.
It seems like mine must have had either an inadequate relief stage in the HT, or more likely got overheated when the factory edge was applied, because I used it for yard work today, which included cutting hardwood and some cardboard breakdown and the edge held up perfectly.
Turns out that third time was the charm and with enough stock removal from the edge I got down to the "good stuff"... this third sharpening went deep of necessity (had to get rid of those big chips) and seems to have finally removed all of the flawed edge steel, I didn't really have any wire edge to speak of either and got a clean apex with ease (same stone progression and just a slightly higher angle than before: 15 DPS, no micro bevel, whereas the first two attempts were at 12.5 DPS).
This behavior is exactly what I'd expect from a craft made Japanese woodworking tool or traditional pattern knife, but not a machine made kiln/salt bath HT'd blade from Sakai... but all's well that ends well, now I have a solution if my V-Toku2 Delica shows the same tendencies!
-David
still more knives than sharpening stones...
still more knives than sharpening stones...
Re: V-toku2 observation and update
Glad to hear everything worked out. My first sharpening of V-toku2 had a stuborn wire edge at 17 dps till I slid the edge on rough leather. The second sharpening at 13 dps had no wire edgeawa54 wrote: ↑Sun Jun 23, 2019 9:01 pmGotta love the little-big D'fly!
I was the one with an Endura that was having terrible wire edging for the first two sharpenings (which I didn't realize the first time 'round, but resolved on the second go) and 1 to 2mm sections of the edge fracturing out with normal cutting tasks.
It seems like mine must have had either an inadequate relief stage in the HT, or more likely got overheated when the factory edge was applied, because I used it for yard work today, which included cutting hardwood and some cardboard breakdown and the edge held up perfectly.
Turns out that third time was the charm and with enough stock removal from the edge I got down to the "good stuff"... this third sharpening went deep of necessity (had to get rid of those big chips) and seems to have finally removed all of the flawed edge steel, I didn't really have any wire edge to speak of either and got a clean apex with ease (same stone progression and just a slightly higher angle than before: 15 DPS, no micro bevel, whereas the first two attempts were at 12.5 DPS).
This behavior is exactly what I'd expect from a craft made Japanese woodworking tool or traditional pattern knife, but not a machine made kiln/salt bath HT'd blade from Sakai... but all's well that ends well, now I have a solution if my V-Toku2 Delica shows the same tendencies!
Every Steel Has Its Appeal :cool:
A.S.O.K.A Edge on Youtube
A.S.O.K.A Edge on Youtube
- bearfacedkiller
- Member
- Posts: 11412
- Joined: Sat Jan 04, 2014 1:22 pm
- Location: hiding in the woods...
Re: V-toku2 observation and update
Good stuff!
-Darby
sal wrote:Knife afi's are pretty far out, steel junky's more so, but "edge junky's" are just nuts. :p
SpyderEdgeForever wrote: Also, do you think a kangaroo would eat a bowl of spagetti with sauce if someone offered it to them?