Page 1 of 15

FRN Jester Sprint Input Needed

Posted: Mon Jun 02, 2014 3:20 pm
by jabba359
In the other thread about a Jester sprint run, Sal expressed his willingness to get one made:
sal wrote:We've already produced a green Jester. In order to make a new sprint, it would have to change from previous models (so as not to hurt the value of previous models). You can agree on a color that we've not used before, agree on an edge config or both and we'll do a run.

sal
So I'm making a poll to help gauge our interest in different colors. You can select more than one (but probably be best to select just your top two or three).

I went thorough the thread and tried to find the most popular colors. I also don't know if GITD is possible, but tossed it in there as I ran out of ideas for other colors. Sal said that lime green has already been done and a color change would be required in the sprint, so I'm not including it in the poll, but feel free to ask for it in the comments.

The following colors have been used in the FRN Jester, so they are also not included in the poll:

*black
*lime green
*pink
*forest green
*blue (Japan only)
*red (Japan only)

Also, please state your interest in edge configuration.

Posted: Mon Jun 02, 2014 3:24 pm
by gdwtvb
Purple seems like a natural.

Grizz

Posted: Mon Jun 02, 2014 3:25 pm
by bearfacedkiller
Keep in mind that ZDP and serrations don't mix well so that may be a factor. We also need to figure out if flat ground will work with the jimping on the nose of the blade. I am going to suggest hollow ground blades for that reason but if flat ground will work well then I am very interested in that too. I know lime green has been used but was unsure if a coated blade would be an exception or not. Also not sure if british racing green is too close to forest green. A Jester Salt would be cool.

I like British racing green with hollow ground ZDP plain edge

or

Lime green with hollow ground ZDP plain edge with black blade

or

Yellow with hollow ground H1 serrated edge. Jester Salt.





Edit: I voted green before I saw yellow and you can't go back and add a vote. Oh well.

Posted: Mon Jun 02, 2014 3:32 pm
by jabba359
I'd prefer one in PE, but would pick one up in SE if that were all that was available.

Posted: Mon Jun 02, 2014 3:33 pm
by LC Kid
Hi Folks!


I would say:
:) - ZDP-189 Hollow Grind PE

- Orange FRN
- Yellow FRN

Posted: Mon Jun 02, 2014 3:46 pm
by FDE
I voted white because it can easily be turned into any color of your choosing! I would like PE in any steel (vg-10 would be fine)

Posted: Mon Jun 02, 2014 4:14 pm
by ZL1
Could we get one in Ron Burgundy?

Posted: Mon Jun 02, 2014 4:45 pm
by bh49
British racing green and orange will be my top choices. All others will be ok, probably except yellow. Will have to die it.

Posted: Mon Jun 02, 2014 5:17 pm
by 3rdGenRigger
Burgundy
Navy Blue
Tan

Posted: Mon Jun 02, 2014 5:18 pm
by GoldenSpydie
Spyderco doesn't do much with moonglow/glow-in-the-dark, so that is my first choice.

Navy blue is my second choice.

Strongly prefer plain edge.

It will be great to get a new sprint!

Posted: Mon Jun 02, 2014 5:20 pm
by Blerv
I voted for Burgundy, British Racing Green, and Grey simply on the off-chance Spyderco would feel the guilt to change up the steel from VG10 :p . Of those, burgundy would be my style fave.

Posted: Mon Jun 02, 2014 6:02 pm
by kbuzbee
Burgundy or BRG in ZDP PE.

Ken

Posted: Mon Jun 02, 2014 6:03 pm
by araneae
I'm sticking with Lime green until Sal states that the reasons we pointed out are not sufficient- second choice is orange. I just don't think that previously used colors have to be ruled out as the old models were pinned and did not have the steel stamped on the tang. It will be very easy to distinguish a new production from the old.

Posted: Mon Jun 02, 2014 6:09 pm
by ohcyclist
Glow in the dark would be amazing for a key chain knife. Delighted that it was listed as an option.

Navy or BRG if that is not an option.

Plain edge is fine, VG-10 or ZDP would be great as well. I vote for hollow ground, not flat.

Per the other thread, I would be over the moon if Spyderco saw fit to make this in grey frn and super blue!!!!!

Posted: Mon Jun 02, 2014 6:12 pm
by Ned
Yes, I voted glow in the dark...ZDP! :)

Posted: Mon Jun 02, 2014 6:15 pm
by Invective
I voted BRG, Purple and GITD. BRG because, y'know, ZDP :p . Purple because it's a great color and GITD because then you can put it on your keys and if you lose your keys, just turn on the lights for a few minutes turn them off and then you can find them!

Posted: Mon Jun 02, 2014 6:28 pm
by xceptnl
I voted White and Navy Blue. I figured unique colors that hadn't been done before would be best. I prefer HG and any of the Japanese steels would suit me fine in either edge configuration. I would still like to put in a lonely vote for RED!

Posted: Mon Jun 02, 2014 7:39 pm
by araneae
Also, I hate to rain on the parade, but glow in the dark FRN is is a bit of a unicorn as far as I know. It has never been done to my knowledge.

Posted: Mon Jun 02, 2014 8:26 pm
by opusxpn
I voted Burgundy as first choice but Navy blue and tan are also good choices.

Posted: Mon Jun 02, 2014 8:30 pm
by bearfacedkiller
Yellow isn't doing so well. I guess the Jester Salt isn't going to be a winner. I think a Jester Salt would go very well with the Ladybug Hawkbill Salt.