A few spyderco prototype videos from IWA
- Mr Blonde
- Member
- Posts: 7652
- Joined: Fri Sep 24, 2004 10:33 am
- Location: The Netherlands, Europe, Earth
- Contact:
Spyderco 2013 Concept Model Video - ClipiTool
Eric Glesser presents the ClipiTool, an upcoming concept model knife/tool combo by Spyderco.
[video=youtube_share;zj-8MZvAScg]http://youtu.be/zj-8MZvAScg[/video]
[video=youtube_share;zj-8MZvAScg]http://youtu.be/zj-8MZvAScg[/video]
- Pinetreebbs
- Member
- Posts: 1833
- Joined: Sat Jun 26, 2010 6:55 am
- Location: SC
I have been waiting for the ClipiTool to replace my little SAK on my key chain.
I just hope the screwdriver will fit these two computer screws:
I just hope the screwdriver will fit these two computer screws:
Have you joined Knife Rights yet?
Go to: http://www.KnifeRights.org
Protecting your Right to own and carry the knives YOU choose.
Go to: http://www.KnifeRights.org
Protecting your Right to own and carry the knives YOU choose.
right :)Mr Blonde wrote:Thanks but it's all Spyderco's fault. I really just stand there, ask Eric to help make a video, point the camera and push the button. :)
"People sleep peaceably in their beds at night only because rough men stand ready to do violence on their behalf"
My top choices Natives5, Calys, C83 Persian
My top choices Natives5, Calys, C83 Persian
- Pinetreebbs
- Member
- Posts: 1833
- Joined: Sat Jun 26, 2010 6:55 am
- Location: SC
True!Jazz wrote:Just file it until it fits. I might get one and mod it to fit my glasses screws.
Have you joined Knife Rights yet?
Go to: http://www.KnifeRights.org
Protecting your Right to own and carry the knives YOU choose.
Go to: http://www.KnifeRights.org
Protecting your Right to own and carry the knives YOU choose.
- Mr Blonde
- Member
- Posts: 7652
- Joined: Fri Sep 24, 2004 10:33 am
- Location: The Netherlands, Europe, Earth
- Contact:
Spyderco 2013 Concept Model Video – Chaparral 3
I saved the Chaparral 3 for the last video I shot at the IWA show. This knife is one of my favorites and Eric Glesser was kind enough to help me shoot this video. Although I have no concrete info, I'm guessing this won't be a cheap knife. I suspect the handle on this Chaparral 3 takes a lot of machining time, and with those close tolerances, it can't be cheap. In my opinion, the stepped titanium pattern is even nicer in persan than in video or pictures. The ergos were great too, no sharp edges where they shouldn't be.
[video=youtube_share;FM_RRLVG7YA]http://youtu.be/FM_RRLVG7YA[/video]
[video=youtube_share;FM_RRLVG7YA]http://youtu.be/FM_RRLVG7YA[/video]
- Mr Blonde
- Member
- Posts: 7652
- Joined: Fri Sep 24, 2004 10:33 am
- Location: The Netherlands, Europe, Earth
- Contact:
I got some extra info from Spyderco on this knife. The Serrata will feature a full flat grind in production, not the appleseed grind Eric discusses on this prototype. I added this comment to the video.
[video=youtube_share;jSIer5vycz8]http://youtu.be/jSIer5vycz8[/video]
[video=youtube_share;jSIer5vycz8]http://youtu.be/jSIer5vycz8[/video]
Is there any additional nformation available on the new Delica 5 mentioned by Mr. Glesser?
** Endura 1 SE G2, Delica 1 CE G2, Co-Pilot SE Almite G2, Bob Terzuola Jr CE ATS-34, Rescue Jr SE ATS-55, Caly 3 PE VG-10 G10, Lady Bug II SE AUS-6, Delica 4 PE VG-10, Endura 4 CE Vg-10, Lady Bug 3 PE VG-10, Cricket SE VG-10, Salt 1 PE H1, Dragonfly 2 PE VG-10, UK Penknife PE CTS BD1 **
Thanks, Mr. Blonde. Below is the reference I was referring to. Hopefully we will hear more later.
Originally Posted by Sal Glesser
"The Lt Wt Delica 5 "concept model" shown in A'dam was linerless. Eric will add bits of steel reinforcement where necessary, but overall the model is quite light and stronger than the current model.
sal"
Originally Posted by Sal Glesser
"The Lt Wt Delica 5 "concept model" shown in A'dam was linerless. Eric will add bits of steel reinforcement where necessary, but overall the model is quite light and stronger than the current model.
sal"
** Endura 1 SE G2, Delica 1 CE G2, Co-Pilot SE Almite G2, Bob Terzuola Jr CE ATS-34, Rescue Jr SE ATS-55, Caly 3 PE VG-10 G10, Lady Bug II SE AUS-6, Delica 4 PE VG-10, Endura 4 CE Vg-10, Lady Bug 3 PE VG-10, Cricket SE VG-10, Salt 1 PE H1, Dragonfly 2 PE VG-10, UK Penknife PE CTS BD1 **
-
- Member
- Posts: 299
- Joined: Fri Feb 25, 2011 2:38 pm
- Location: Texas
- The Deacon
- Member
- Posts: 25717
- Joined: Fri Sep 24, 2004 10:33 am
- Location: Upstate SC, USA
- Contact:
Was there a concept model of an unlined FRCP Native 5 at either?Mr Blonde wrote:Not from me, and I didn't see any Delica 5 proto at either the amsterdam meet or at the IWA show.
Given that, up to that point, he'd been talking about the new FRCP Native 5, I'm guessing the "Delica 5" reference may have simply been a mistake.FrankH wrote:Thanks, Mr. Blonde. Below is the reference I was referring to. Hopefully we will hear more later.
Originally Posted by Sal Glesser
"The Lt Wt Delica 5 "concept model" shown in A'dam was linerless. Eric will add bits of steel reinforcement where necessary, but overall the model is quite light and stronger than the current model.
sal"
Paul
My Personal Website ---- Beginners Guide to Spyderco Collecting ---- Spydiewiki
Deplorable :p
WTC # 1458 - 1504 - 1508 - Never Forget, Never Forgive!
My Personal Website ---- Beginners Guide to Spyderco Collecting ---- Spydiewiki
Deplorable :p
WTC # 1458 - 1504 - 1508 - Never Forget, Never Forgive!