Discuss Spyderco's products and history.
Jeff/1911
Member
Posts: 1390 Joined: Fri Sep 24, 2004 10:33 am
Location: Western Canada
#1
Post
by Jeff/1911 » Fri Oct 12, 2001 12:00 am
So, which Spydie do you think would make the best pumpkin carving knife? This idea came up tonight as I tried to decide which of mine I’d use on the weekend. I think I’ve finally settled upon my stainless serrated Police. How about you? Why do you think so? Cheers, Jeff/1911.
charlie
Member
Posts: 248 Joined: Fri Sep 24, 2004 10:33 am
Location: Santa Maria, CA USA
#2
Post
by charlie » Fri Oct 12, 2001 9:36 am
My Frank Centofante C50G should do just great for carving with it's spearpoint 3 5/8" blade and a Spyder Edge. Some other Spyderco models that fit the sharp point, slim long blade catagory: Police, Rookie, Endura, Catcherman, Dyad C44, and Howard Viele C42.
chinook
Member
Posts: 1086 Joined: Fri Sep 24, 2004 10:33 am
Location: southern Oregon coast USA
#3
Post
by chinook » Fri Oct 12, 2001 12:09 pm
This was in response to a question about taking out a splinter, butt seems to fit this thread too. Along with possibly the worst pumpkin carver.
Naw.... actually the Q would probably be the worst. The cleanup would be horrible. <img src="smile.gif" width=15 height=15 align=middle>
Disguised as a responsible adult
Jeff/1911
Member
Posts: 1390 Joined: Fri Sep 24, 2004 10:33 am
Location: Western Canada
#4
Post
by Jeff/1911 » Fri Oct 12, 2001 2:11 pm
Excellent suggestions fellows...anybody else?
Jeff/1911.
ftkinney
Member
Posts: 527 Joined: Fri Sep 24, 2004 10:33 am
Location: Texan living in New Jersey USA
#5
Post
by ftkinney » Fri Oct 12, 2001 2:12 pm
i would use a fixed blade due to clean up.
chinook what knife is that second from the top with the little lever on the side.
FTK
Clay Kesting
Member
Posts: 1241 Joined: Fri Sep 24, 2004 10:33 am
Location: Sydney Australia
#6
Post
by Clay Kesting » Fri Oct 12, 2001 2:42 pm
With out a doubt, the ultimate pumpkin carver is the Paring knife from the Pro Culinaire series.
Clay
Don't worry that the world might end tomorrow, in Australia it's tomorrow already.
thorin hammer
Member
Posts: 180 Joined: Fri Sep 24, 2004 10:33 am
Location: Topeka, Kansas USA
#7
Post
by thorin hammer » Fri Oct 12, 2001 3:44 pm
I second what Clay said.
Some laws permit, what honor dose not.
Knife Knut
Member
Posts: 1039 Joined: Fri Sep 24, 2004 10:33 am
Location: South Carolina
#8
Post
by Knife Knut » Fri Oct 12, 2001 7:07 pm
DO NOT USE A DREMEL OR OTHER ROTARY TOOL
It makes a mess, is too short, and difficult to make precision cuts w/
I agree that a long thin blade would work well.
(hmm maybe I should get a Catcherman in time for halloween)
chinook
Member
Posts: 1086 Joined: Fri Sep 24, 2004 10:33 am
Location: southern Oregon coast USA
#9
Post
by chinook » Fri Oct 12, 2001 7:07 pm
ftkinney...
That is the C50GS Centofante II and that slide switch is the Securlock feature designed by Frank Centofante which blocks and locks the blade in the open position.
It has been discontinued and some good buys can be found on it now and the smaller C25 which also has the Securlock.
The pic here shows the smaller version in locked position.
Disguised as a responsible adult
aero_student
Member
Posts: 735 Joined: Fri Sep 24, 2004 10:33 am
Location: Folsom, CA, USA, Earth USA
#11
Post
by aero_student » Fri Oct 12, 2001 8:56 pm
My best guess would be the moran,
ftkinney
Member
Posts: 527 Joined: Fri Sep 24, 2004 10:33 am
Location: Texan living in New Jersey USA
#12
Post
by ftkinney » Sat Oct 13, 2001 12:42 am
thanks chinook i really like the look of that knife i might try to find one.
FTK
Blades
Member
Posts: 1926 Joined: Fri Sep 24, 2004 10:33 am
Location: Fayetteville, NC USA
#13
Post
by Blades » Sat Oct 13, 2001 9:14 pm
What about the Calypso??
Blades
Blades
Member
Posts: 1926 Joined: Fri Sep 24, 2004 10:33 am
Location: Fayetteville, NC USA
#14
Post
by Blades » Sat Oct 13, 2001 9:18 pm
Whoops.
Blades
Edited by - Blades on 10/14/2001 10:40:19 PM
Jeff/1911
Member
Posts: 1390 Joined: Fri Sep 24, 2004 10:33 am
Location: Western Canada
#15
Post
by Jeff/1911 » Sun Oct 14, 2001 12:24 am
Blades, I think the Calypso will make a wonderful choice for jack-o-lantern-ization. I intend to try mine, along with my serrated Police.
Cheers, Jeff/1911.
Blades
Member
Posts: 1926 Joined: Fri Sep 24, 2004 10:33 am
Location: Fayetteville, NC USA
#16
Post
by Blades » Sun Oct 14, 2001 10:50 pm
I guess I need to buy a Calypso before Hallowen!! <img src="smile.gif" width=15 height=15 align=middle>
Blades
Jeff/1911
Member
Posts: 1390 Joined: Fri Sep 24, 2004 10:33 am
Location: Western Canada
#17
Post
by Jeff/1911 » Mon Oct 15, 2001 11:28 pm
Hey, great reason/excuse. Grin...Jeff/1911.
Knife Knut
Member
Posts: 1039 Joined: Fri Sep 24, 2004 10:33 am
Location: South Carolina
#18
Post
by Knife Knut » Mon Jan 14, 2002 4:17 pm
So how did it work out?
aero_student
Member
Posts: 735 Joined: Fri Sep 24, 2004 10:33 am
Location: Folsom, CA, USA, Earth USA
#19
Post
by aero_student » Mon Jan 14, 2002 6:40 pm
I used a moran drop point and it went right through them pumpkin. It was also easy to clean up.