Get me excited about M398

A place to share your experience with our Mule Team knives.
TTFulltimer
Member
Posts: 111
Joined: Wed Feb 01, 2023 12:25 pm

Re: Get me excited about M398

#41

Post by TTFulltimer »

Ogre wrote:
Sun Mar 05, 2023 8:36 pm
Hawaii808 wrote:
Fri Nov 18, 2022 2:39 pm
What angle to sharpen at do you guys think will be good for the m398?
I too am wondering what a good edge angle for this steel would be. I'm seeing another brand put a 14° edge on CPM-S90V and CPM-154. With M398 being high on edge retention but low on toughness, would a 15° or 17° be prone to chipping? Or, should I opt for a 25°ish? I'm thinking this will be, primarily, my bird and trout... (and cardboard) knife.
Get on real computer, go to You Tube, and watch edge "Stability" routines this man does. Some supposedly low toughness steels really do hold up very well at the edge. Any site on a phone is about 1/4 as good as a site on a real computer. The code for the phone and the mobile site it directs you to are "light" so any phone can display the short form content. You buy the phone with the whiz bang processor, but the processor gets fed bread and water.

https://www.youtube.com/@FearNoSteel

The toughness test takes a bar of metal, supports it on both ends and then slams a weight into the middle to break it. A long standing metal test. However, it is more about a bulk property when you use the metal to make tooling. Edge stability is a product of the elastic strength of the steel where it deforms and pops back like a spring. And the ultimate strength of a steel where it is actually breaks. Many steels have properties that allow it to bend past springing back a long way before it breaks reaching ultimate strength. On the edge your failure may just be a roll in the edge, plastic deformation, or a loss of a piece of edge, ultimate failure.

The M398 Mule has been tested and the HRC is around 64. That from my research is what people have had custom knife makers provide in M398 as a sweet spot. At 62 it lacks some. That referenced You Tuber above has done a knife in M398 at 66HRC.
Just a crotchety old curmudgeon who has seen a thing or two
Steeltoez83
Member
Posts: 387
Joined: Sat Aug 01, 2020 8:51 am

Re: Get me excited about M398

#42

Post by Steeltoez83 »

I own that knife from triple b at 66 hrc. In my toughness testing it was middle of the pack. It's edge retention rivaled s90v and zdp189. It sharpens up very easily but that's a combo of geometry and Shawn's heat treat. I ordered a couple mules bcuz I grew tired of waiting for production offering from spyderco. I generally prefer posting my edge retention testing with accessible options not customs.
"Nothing is built on stone; all is built on sand, but we must build as if the sand were stone."
Ogre
Member
Posts: 3
Joined: Sun Mar 05, 2023 8:07 pm

Re: Get me excited about M398

#43

Post by Ogre »

Awesome! Thx folks!
SpiderIsland
Member
Posts: 31
Joined: Sun Mar 05, 2023 2:27 pm

Re: Get me excited about M398

#44

Post by SpiderIsland »

As someone who enjoys a fixed blade in the outdoors, I was thinking of M398 Mule.
Would this take well to bushcrafting / wood cutting tasks or is it more for around the home and office / warehouse ?
Dog spelled backwards is…
Steeltoez83
Member
Posts: 387
Joined: Sat Aug 01, 2020 8:51 am

Re: Get me excited about M398

#45

Post by Steeltoez83 »

Screenshot_20230310_182229_Gallery.jpg
Mule arrived today. I tested the factory edge and I got 370. When testing the edge for overall sharpness during testing, it has a very aggressive bite. It has 30% carbide volume which is not a shocker. I could feel the carbides when I was testing the edge for sharpness.
"Nothing is built on stone; all is built on sand, but we must build as if the sand were stone."
User avatar
Bolster
Member
Posts: 5573
Joined: Sat Mar 03, 2007 1:27 pm
Location: CalyFRNia

Re: Get me excited about M398

#46

Post by Bolster »

SpiderIsland wrote:
Fri Mar 10, 2023 2:50 pm
As someone who enjoys a fixed blade in the outdoors, I was thinking of M398 Mule.
Would this take well to bushcrafting / wood cutting tasks or is it more for around the home and office / warehouse ?

Doesn't bushcraft and woodwork generally do best with a steel that is reasonably tough? Larrin reports M398 “toughness ... lower than any other available stainless knife steel, including S125V” at around 3 ft lbs. If you do use for woodwork, no twisting cuts, eh?
Steel novice who self-identifies as a steel expert. Proud M.N.O.S.D. member 0003. Spydie Steels: 4V, 15V, 20CV, AEB-L, AUS6, Cru-Wear, HAP40, K294, K390, M4, Magnacut, S110V, S30V, S35VN, S45VN, SPY27, SRS13, T15, VG10, XHP, ZWear, ZDP189
SpiderIsland
Member
Posts: 31
Joined: Sun Mar 05, 2023 2:27 pm

Re: Get me excited about M398

#47

Post by SpiderIsland »

Bolster wrote:
Fri Mar 10, 2023 7:52 pm
SpiderIsland wrote:
Fri Mar 10, 2023 2:50 pm
As someone who enjoys a fixed blade in the outdoors, I was thinking of M398 Mule.
Would this take well to bushcrafting / wood cutting tasks or is it more for around the home and office / warehouse ?

Doesn't bushcraft and woodwork generally do best with a steel that is reasonably tough? Larrin reports M398 “toughness ... lower than any other available stainless knife steel, including S125V” at around 3 ft lbs. If you do use for woodwork, no twisting cuts, eh?
Thanks for the insight. I will wait for a stronger steel.
Dog spelled backwards is…
TTFulltimer
Member
Posts: 111
Joined: Wed Feb 01, 2023 12:25 pm

Re: Get me excited about M398

#48

Post by TTFulltimer »

At roughly the same hardness as the Mules. If this is not tough, I have no idea what is.

https://youtu.be/3FYdPN_WvKg
https://youtu.be/L4NRvqtYD8g&t=608s
Just a crotchety old curmudgeon who has seen a thing or two
SpiderIsland
Member
Posts: 31
Joined: Sun Mar 05, 2023 2:27 pm

Re: Get me excited about M398

#49

Post by SpiderIsland »

TTFulltimer wrote:
Sat Mar 11, 2023 12:06 pm
At roughly the same hardness as the Mules. If this is not tough, I have no idea what is.

https://youtu.be/3FYdPN_WvKg
https://youtu.be/L4NRvqtYD8g&t=608s
WOW! Some testing.
That gentleman does not hold back.
Now I will check the hardness on the Spyderco M398. 👍
Dog spelled backwards is…
Steeltoez83
Member
Posts: 387
Joined: Sat Aug 01, 2020 8:51 am

Re: Get me excited about M398

#50

Post by Steeltoez83 »

Tested a 400 super vit diamond edge and got 550 cuts. Factory edge got 370 and this edge got 550.
"Nothing is built on stone; all is built on sand, but we must build as if the sand were stone."
User avatar
Traditional.Sharpening
Member
Posts: 282
Joined: Thu Mar 02, 2023 12:29 am

Re: Get me excited about M398

#51

Post by Traditional.Sharpening »

TTFulltimer wrote:
Sat Mar 11, 2023 12:06 pm
At roughly the same hardness as the Mules. If this is not tough, I have no idea what is.

https://youtu.be/3FYdPN_WvKg
https://youtu.be/L4NRvqtYD8g&t=608s
I can assure you this is unlikely to be the same heat treat that you receive in the Mule's.... unless Luong of BCMW has somehow partnered with Spyderco to use this heat treat. Luong has been long developing his heat treat protocols and gotten some really impressive results but to my knowledge he has not given any of this over to knifemakers for their own uses. The last I spoke with him he was looking more at selling his work to industry in general, not so much cutlery. I can't remember what industry he spoke of, maybe cars, etc.
alphaneuron9
Member
Posts: 143
Joined: Sun Nov 07, 2021 8:08 am

Re: Get me excited about M398

#52

Post by alphaneuron9 »

I am super excited. I think it will make an excellent hunting/skinning knife.

I saw a youtube video of an M398 chopper pulverizing a 2 by 4! It was 65 HRC! https://youtu.be/3FYdPN_WvKg

Anyone know the hardness of our M398 mule?

:bug-red-white
Alex
Scientia et pax
tcarltonw
Member
Posts: 199
Joined: Sat Apr 23, 2022 8:18 pm

Re: Get me excited about M398

#53

Post by tcarltonw »

Steeltoez83 wrote:
Sun Mar 12, 2023 8:39 am
Tested a 400 super vit diamond edge and got 550 cuts. Factory edge got 370 and this edge got 550.
Appreciate the tests that you do.
TTFulltimer
Member
Posts: 111
Joined: Wed Feb 01, 2023 12:25 pm

Re: Get me excited about M398

#54

Post by TTFulltimer »

alphaneuron9 wrote:
Sun Mar 12, 2023 8:35 pm
I am super excited. I think it will make an excellent hunting/skinning knife.

I saw a youtube video of an M398 chopper pulverizing a 2 by 4! It was 65 HRC! https://youtu.be/3FYdPN_WvKg

Anyone know the hardness of our M398 mule?

:bug-red-white
64ish
Just a crotchety old curmudgeon who has seen a thing or two
Steeltoez83
Member
Posts: 387
Joined: Sat Aug 01, 2020 8:51 am

Re: Get me excited about M398

#55

Post by Steeltoez83 »

tcarltonw wrote:
Mon Mar 13, 2023 3:40 am
Steeltoez83 wrote:
Sun Mar 12, 2023 8:39 am
Tested a 400 super vit diamond edge and got 550 cuts. Factory edge got 370 and this edge got 550.
Appreciate the tests that you do.
Thankyou.
"Nothing is built on stone; all is built on sand, but we must build as if the sand were stone."
Steeltoez83
Member
Posts: 387
Joined: Sat Aug 01, 2020 8:51 am

Re: Get me excited about M398

#56

Post by Steeltoez83 »

Screenshot_20230313_124904_Gallery.jpg
Today's testing with a 10-11 dps super vitrified triple b stone at 1k achieved 720 cuts in my testing today. Surprised not many gave this steel a fair shake when it dropped 4 months ago.
Attachments
Screenshot_20230313_125020_Gallery.jpg
"Nothing is built on stone; all is built on sand, but we must build as if the sand were stone."
TTFulltimer
Member
Posts: 111
Joined: Wed Feb 01, 2023 12:25 pm

Re: Get me excited about M398

#57

Post by TTFulltimer »

Steeltoez83 wrote:
Mon Mar 13, 2023 11:55 am
Today's testing with a 10-11 dps super vitrified triple b stone at 1k achieved 720 cuts in my testing today. Surprised not many gave this steel a fair shake when it dropped 4 months ago.
Listening To "Experts" Yes I capitalized the LT on purpose.
Just a crotchety old curmudgeon who has seen a thing or two
spook2517
Member
Posts: 5
Joined: Sun Sep 25, 2022 8:46 pm

Re: Get me excited about M398

#58

Post by spook2517 »

I know, I know, this isn’t the purpose and it annoys the forum - but this is my best kitchen knife. I use it for everything. Blade is still sharp & no rust.
User avatar
attila
Member
Posts: 1812
Joined: Fri Apr 29, 2016 9:20 am
Location: Maryland

Re: Get me excited about M398

#59

Post by attila »

spook2517 wrote:
Mon Mar 13, 2023 2:32 pm
I know, I know, this isn’t the purpose and it annoys the forum - but this is my best kitchen knife. I use it for everything. Blade is still sharp & no rust.
It’s your knife; use it in the kitchen if you want to, and don’t worry about naysayers! I use my Magnacut and B70P Mules in the kitchen too. They’re great for deboning chicken and turkey. The B70P was made when Mules weren’t thiccc behind the edge, so it’s great for dicing tasks as well.
Have: old S30V Native, HAP40 Endura, ZDP DF2, S110V Manix LW, Cru-wear Para 3, SE H1 DF2, S90V Native 5, K390 Urban, SE Pac Salt, P.I.T.S., XHP Manix LW, SB Caly 3, B70P, PMA11, K03, Kapara, REX 45 Military, 154CM Manix LW, Swick, AEB-L Urban, KC Cruwear Manix, M390 PM2, Mantra 2, CruCarta Shaman, M390 Manix, K390 Police 4, S90V Manix LW, Rex 45 Manix LW, 20CV Manix, Rex 45 Lil’Native, Shaman, C208GP, Cruwear Manix, Cruwear Manix, M4 Chief, Z-max!!!

Want: SPY27, K490, Swick 5
.
User avatar
Traditional.Sharpening
Member
Posts: 282
Joined: Thu Mar 02, 2023 12:29 am

Re: Get me excited about M398

#60

Post by Traditional.Sharpening »

attila wrote:
Mon Mar 13, 2023 4:14 pm
spook2517 wrote:
Mon Mar 13, 2023 2:32 pm
I know, I know, this isn’t the purpose and it annoys the forum - but this is my best kitchen knife. I use it for everything. Blade is still sharp & no rust.
It’s your knife; use it in the kitchen if you want to, and don’t worry about naysayers! I use my Magnacut and B70P Mules in the kitchen too. They’re great for deboning chicken and turkey. The B70P was made when Mules weren’t thiccc behind the edge, so it’s great for dicing tasks as well.
Are you suggesting the newer Mule's are thick behind the edge compared to older examples? Mine in M398 and Rex 76 seemed relatively thin for a production knife but I've never experienced any older Mule's to compare to. What sort of edge geometry do these come with 15-20 DPS?
Post Reply