I am considering having scales made with a water jet. I need drawings to supply info to expedite the finishing steps for scales. Are there any drawings available? I have not located any to date. My plan is to use thin slices of cool stone patterns for...
Have a set of 3D printed scales made by our resident guru FullScaler to give away to an Australian. Won them in one of his giveaways so happy to send them on via a giveaway.
Post a please and I will pick who the lucky owner will be if I get...
I received an Aebl Mule and have never been so much, on the fence about a blade before. By my eye it appeared to be ground a little deep, and the leftover burr is obvious. I did spend a fair week weighing pros and cons of sending it back to Spyderco....
But !
A) The shape makes it hard to index the Mule in the hand for various tasks ( Curved grip )
B) The grip is a little cramped for my hand ( I had to stretch my Mule )
C) The Mule is not super comfortable for...
I'm not the only one to notice how the M398 Mule gracefully transitioned to, Out of Stock nearly the same time the Aebl Mule came, In Stock. No empty shelf, no FOMO, happy customers. Aebl Mule happily holds the title, In Stock until... well...
Hello fellow spider enthusiasts! I have been working on a sheath that is nearly entirely 3d printed. It does require 6 M3 bolts/nuts. It can be printed without supports, but I recommend them, only for the recesses for the nuts/bolts.
The thumb ramp on the Mule is abrupt, and prone to hurt the thumb when using sabre grip, if the blade stops short. Would the mule series be ruined if the thumb ramp were relaxed a few degrees in upcoming mules? More of a Manix-style thumb ramp, perhaps?...
This is the only way I am really keen to see Spyderco modify the Mule platform. A PE and SE of each future Mule release would be fantastic. Also, releasing serrated versions of past steels would be... add superlative.
Ultem®
High strength plastic with outstanding electrical and high service temperature properties
Ultem® (polyetherimide) is a semi-transparent high strength plastic material that can operate in high service...
I was thinking it would be cool if all the steels Spyderco's used in the past could have a Mule. There a few steels the came and went before the Mule Team project started. I know there's ones that probably won't make sense like Aus6 or the most likely...
I was a little surprised not to see an actual performance thread rather other than sharpening and first impressions. Hopefully this thread will begin receiving some additional feedback (or linked to the current running performance thread that I am unaware...
I just wanted to give a quick review and some pictures of some scales that I picked up on Etsy from Philip over at Hazy Design Studio (@Hazy_Design_Studio on Instagram and HazyDesignStudio on Etsy)
After seeing Gtscotty's scales here I decided to try my hand at it. I'm not sure how he did it but the way I went about it was very convoluted so I don't think I can explain easily. Here's pictures of both still in fusion because I wanted feedback on how...
Sal asked for the following poll, after a discussion between Sal and forumite chkn. You may want to read that exchange before voting (see pages 3 & 4 of This poll runs for two weeks and allows changing of your vote.
I know there is Forum knife chatter but how about a MuleTeam Forum knife? If we could decide on a team name would you want that on there or just MT Forum 202x? Perhaps a nice Damascus or even the elastic ceramic? Maybe revisit a previous steel? Maybe a...
Speaking of mules how does everyone sharpen theirs? I use the Work Sharp guided system with reasonable results. Since this is pretty much free hand it is easy to be off on your angle by a few degrees. On the plus side there is something cool about free...
First attempt at Mule handles. First, I traced out the Halpern contoured scale, and cross-ripped the board by hand. I don't have a real saw that will do this.
I traced the handles again onto the blanks, then tried about a dozen things to figure out...
Hi everyone, I am new to the Mule scene (been on the forums for a couple of months now) and managed to snag a Z-Max Mule earlier this week. I'm planning on building my own scales for it once it arrives and have decided on G10 as the handle material. I'm...
A newby to this Mule thing. I always try to do a deep dive when I discover something. So far I am not aware that all the information about a mule is available when it is released. HRC is only found after someone or other gets the mule and tests it or has...
I spent many hours trying to find the hardness of the MT38 mule in M398. I could not find one thing.
It is wonderful to have Larrin Thomas addressing the metallurgy of steels, in particular to knives. Unfortunately we cannot buy one piece of treated...
I've always liked the Atwood PerfBaby tool, pictured below. I'm wondering if a PerfBaby Mule with a pair of translucent printed scales would look neat, or no scales at all for ultralight backpacking use. I think that drilling holes in hardened steel is...
This is the first version of my 3d printed sheath that's going to be matched up to my scale designs. It is a 2 piece clam-shell that uses the Spydiehole for retention. The belt clip still needs designed, not sure how it's gonna look yet. Once I test and...
Nearly everyone that makes a Mule handle has to drill some holes I assume. If you have some good tips or ideas for people who might be trying to figure out how to drill their handle holes or maybe learning to use a drill press for the first time this is...
Hi, I’m looking for some advice from the Mule experts.
I bought a ZDP Mule second then decided to use the factory scales. The barrels in the scale kit will not pass completely through the scales. They only ‘fit’ from the presentation side and stop...
I ordered a new Mule Team 2 and a leather sheath last week and the box arrived yesterday. Opened her up and no blade! Spyderco packed the box with my sheath but forgot to ship the knife even though it was clearly printed on the enclosed packing slip. A...
Does anyone know where I can find these? I can find similar ones, they have a flat thick top not the button or dome shape like these. I want to try my hand at making handles and these look the easiest to work with, providing I can find more. These came...
Hopefully it will help future Spyderfans ease into the Mule Team. I know some, including myself have gone FOMO/bonkers/nutty over trying to time the release of a limited Mule.
Also, thank you very much for producing enough M398 that there is stock and no...
... but I ordered a wide range of silicon carbide sandpaper from maker material supply and didn't consider that it would come as a stack of loose sheets. In the name of work flow, how do yall store/set up your bulk sand paper?
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum