Spyderco Forums

On today's evening news was an article about a baby Humpback whale. http://khon2.com/2014/12/12/crews-free-entangled-humpback-whale-off-maui/ I am sure you will recognized the backward facing blade with it's prominent thumb hole. Nice to see your work doing it's job. Huh, Sal The baby had been attac...

These are most likely scratches that you, or someone else, inadvertently got on the blade while using the knife and did not notice them. The fact that they are parallel also speaks to that. H1 scratches if you look at it wrong. In other words, it scratches very, very easily. Gee Doc Dan, before you...

Where did you purchase the knife? Given that there are counterfeit Dragonfly Salts on the market, and that the steel quality of those is dubious at best, that's always a possibility unless the knife was purchased new from a reputable dealer. Really, that is a good point. H1 is one of the toughest s...

Cliff Stamp wrote:How do you know they are not scratches?

By the same method I use to identify a Buffalo chip, experience.
Plus these cracks run in a straight line and parallel to each other.

The last time I had a problem and took pictures, I was accused of trying to embarrass the Spyderco family. I had not included the pic on this forum, only a way to see them off line. I am not looking for a warranty repair. I will sent the knife to for your review, if you feel I caused the problem I w...

I have had this knife for only a few months. It as been sharpened with the SharpMaker, opened a few envelops and generally kept very protected in my sock drawer. These cracks run in side by side from the tip back, about 1/2 inch. Those at the front are closer than 1/16". These are not scratches...

Beauty is in the eye of the beholder. I know, I look in the mirror several times a day.


weetoots

What is the G10 made of? If it is nylon, you should have great results. Wash with a small amount of liquid dish detergent. I prefer Dawn. Use a small hand brush or tooth brush. What did you use to hold the solution in? I use a medium (1-1.5 gallon) Plastic paint pail. A glass bowl or SS sink. Heat t...

The Deacon,
For my further edification, what is the process for RIT dying? Does one just submerge the knife handle (an assembled knife)? Time of submersion to completely get a black handle?

Thanks

Problem solved . Received email today from Warranty/Repair. My knife is ready to come home. Fees gladly paid. To all who replied, thank you for your replies, positive or slightly negative. I will enjoy my little Manbug even more. Since this knife can rust, overtime, what can I use to kept it lubed ...

The part in bold is confusing Are you saying the manbug you sent in was fake because zdp rusted? That doesn't make sense, but that also doesn't line up with your other quote below asking for a refund or replacement. I hope it works out for you. Bad typing on my part.it was supposed to say "I t...

I've been to that area in HI myself...dry doesn't even come close to describing it. I live in Colorado, and frequently visit Wyoming. These areas are actually "dry." Also, while moist air is one problem, the salt in the air and on everything is very corrosive. That's why the "Salt&qu...

Well, still no satisfaction. After 3 more emails, 2 phone calls with messages left to please call me. Nothing. How expensive is an email? A simple phone call? I am very disgusted with Spyderco's Customer service or should I say lack of customer service. Sal, your company has had my Manbug, zdp-189 s...

Thank you for your replies. Concerning my statement, "this knife is not supposed to rust" is based on the amount of Chromium (CR) contained in the recipe. Chromium (Cr) - Added for increased wear resistance, hardness, tensile strength, and (most importantly) for corrosion resistance. Cr fo...

I hate to write this thread but what I have done on my own has not succeeded. In April, this year, I purchased a Manbug Lightweight, British Racing Green, ZDP-189 from Amazon. What a little beauty, for a while. One day I was looking into the case and saw what looked like rust. Wait a minute, this kn...

Well it is time to get another Spyderco knife. For me, it is not easy to select the perfect knife . Just too many to choose from. I finally settled on an Endura4,C10PSBBK. What a beauty. Is there anything I need to know about sharpening with my Spyderco Tri-Angle Sharpmaker? I can't wait until Frida...

Thanks all. Good info. I'll work my way toward 30.
Mr. Sal, thanks for the welcome.

I read the instructions BUT, I have a good sharp blade with the 40 degree setting. Will I get a better edge with the 30 degree setting. I have the two brown and two white triangles that came with the Sharpmaker, plus I bought the ultra fine, 204 UF1.

Nice knife fits my big hand well.

a popular knife style, that has interchangeable blades made of different compounds. Like a knife blade compound that is good for daily chores, but would rust if you took it fishing, by the sea shore. Or taking it farther, you really like the feel of your grip or you want to try another. Just wonderi...

I am a newbie when it comes to knives. Not the old jack knife I owned when I was 10 and we played mumblety-peg. Yes sir, now 57 years later, I have a knife that is definitely a cut above. (pun intended). I have read a lot reviews in this forum and most were helpful. I am on a limited budget now so i...