Ok thanks
Search found 25 matches
- Wed May 06, 2020 9:37 pm
- Forum: Spyderco General Discussion
- Topic: Adjusting pivot when there are screws on both sides
- Replies: 2
- Views: 598
- Wed May 06, 2020 5:15 pm
- Forum: Spyderco General Discussion
- Topic: Adjusting pivot when there are screws on both sides
- Replies: 2
- Views: 598
Adjusting pivot when there are screws on both sides
Hi guys,
For the Spyderco Para 3 LW, it has pivot screws on both sides. What is the correct approach to adjusting the pivot? Do you tighten one side all the way and use the other side to do the tuning for the pivot? If so, does it matter which side you tighten all the way? Thanks Spyderco community!
For the Spyderco Para 3 LW, it has pivot screws on both sides. What is the correct approach to adjusting the pivot? Do you tighten one side all the way and use the other side to do the tuning for the pivot? If so, does it matter which side you tighten all the way? Thanks Spyderco community!
- Tue May 05, 2020 9:16 pm
- Forum: Spyderco General Discussion
- Topic: I need some clarification before using the Sharpmaker for the first time...
- Replies: 39
- Views: 7394
Re: I need some clarification before using the Sharpmaker for the first time...
Thanks for all the help, I forgot to update it's been a while but it's hair shaving sharp now. Bevels are uneven but only an aesthetic thing and I'm happy the knife is sharp :) Quick question... The pivot has screws on both sides for the Para 3 LW. Is the proper way to tighten one side all the way a...
- Tue Apr 07, 2020 9:02 pm
- Forum: Spyderco General Discussion
- Topic: I need some clarification before using the Sharpmaker for the first time...
- Replies: 39
- Views: 7394
Re: I need some clarification before using the Sharpmaker for the first time...
To be clear, I meant to say that if properly apexed it should be shaving sharp straight off the diamond/cbn rods. If it’s not then you likely aren’t quite there yet. The sharpie can give you a false impression sometimes when you’re close. Meaning it can look like there’s no sharpie left when you re...
- Sat Apr 04, 2020 3:15 pm
- Forum: Spyderco General Discussion
- Topic: I need some clarification before using the Sharpmaker for the first time...
- Replies: 39
- Views: 7394
Re: I need some clarification before using the Sharpmaker for the first time...
Hi Many, if you have properly reprofiled and reached the apex on both sides then your edge should easily slice paper and shave arm hair (assuming you have made some lighter alternating passes to remove any burr. If you don’t have that level of sharpness then you are almost certainly not profiled al...
- Sat Apr 04, 2020 2:18 pm
- Forum: Spyderco General Discussion
- Topic: I need some clarification before using the Sharpmaker for the first time...
- Replies: 39
- Views: 7394
Re: I need some clarification before using the Sharpmaker for the first time...
Hi ManyReason, I would also suggest that you get a magnifier loupe, maybe 10X so you can study the edge as you learn. sal Hey Sal, The loupe actually came early and I got it now. It's a cheap loupe I got on Amazon that has 10x, 20x, and 30x, although the lens for the 20x and 30x are too small, I mo...
- Sat Apr 04, 2020 8:54 am
- Forum: Spyderco General Discussion
- Topic: First time sharpening with sharpmaker and need help
- Replies: 20
- Views: 2710
Re: First time sharpening with sharpmaker and need help
The more you use the sharpmaker, the more you sharpen period, the better you will get. Don't worry too much about being able to slice paper with your right and left hands. I concern myself with does the edge feel the same on both sides? Example, I use my thumb to check the edge. Using my right thum...
- Sat Apr 04, 2020 12:57 am
- Forum: Spyderco General Discussion
- Topic: First time sharpening with sharpmaker and need help
- Replies: 20
- Views: 2710
Re: First time sharpening with sharpmaker and need help
UPDATE: Good news (I think). .... Great that it worked out for you!! I think in hindsight it might be a good thing that you really got into sharpening and reprofiling right from the beginning of your "Spyderco-journey", even if it took a bit of an effort obviously... ;) You say you want &...
- Sat Apr 04, 2020 12:06 am
- Forum: Spyderco General Discussion
- Topic: I need some clarification before using the Sharpmaker for the first time...
- Replies: 39
- Views: 7394
Re: I need some clarification before using the Sharpmaker for the first time...
UPDATE: Good news (I think). After reprofiling my bevel to 30 (15 DPS), I found that my blade still wasn't sharp. I had the flexcut leather strop, applied some compound, and a few low angle and soft passes put my edge pretty sharp to both sides (however after some cutting on paper, one side wasn't s...
- Sat Apr 04, 2020 12:05 am
- Forum: Spyderco General Discussion
- Topic: First time sharpening with sharpmaker and need help
- Replies: 20
- Views: 2710
Re: First time sharpening with sharpmaker and need help
UPDATE: Good news (I think). After reprofiling my bevel to 30 (15 DPS), I found that my blade still wasn't sharp. I had the flexcut leather strop, applied some compound, and a few low angle and soft passes put my edge pretty sharp to both sides (however after some cutting on paper, one side wasn't s...
- Fri Apr 03, 2020 7:03 pm
- Forum: Spyderco General Discussion
- Topic: >30 degree factory bevels
- Replies: 30
- Views: 3027
Re: >30 degree factory bevels
Yea I recently got my Para 3 and one was perfect 15 degrees on one side but the other was a little obtuse angle, I had to reprofile with diamond rods but it's fine at the end, I'm learning and honestly more aesthetic for me! At the moment I have successfully reprofiled that wonky side to 15 degrees...
- Fri Apr 03, 2020 6:49 pm
- Forum: Spyderco General Discussion
- Topic: >30 degree factory bevels
- Replies: 30
- Views: 3027
Re: >30 degree factory bevels
Yea I recently got my Para 3 and one was perfect 15 degrees on one side but the other was a little obtuse angle, I had to reprofile with diamond rods but it's fine at the end, I'm learning and honestly more aesthetic for me! At the moment I have successfully reprofiled that wonky side to 15 degrees ...
- Fri Apr 03, 2020 4:47 pm
- Forum: Spyderco General Discussion
- Topic: First time sharpening with sharpmaker and need help
- Replies: 20
- Views: 2710
Re: First time sharpening with sharpmaker and need help
I have ordered one and it will arrive monday, can't wait to use it
- Fri Apr 03, 2020 4:26 pm
- Forum: Spyderco General Discussion
- Topic: First time sharpening with sharpmaker and need help
- Replies: 20
- Views: 2710
Re: First time sharpening with sharpmaker and need help
Edit now... I'm positive my whole bevel is 30 degrees now. It took a lot of reprofiling but after putting sharpie on both sides, after a lot of passes the sharpie comes off on both sides at 30 degrees. Now, I can't cut paper when coming off the diamond rods. I'm making sure to progressively use very...
- Thu Apr 02, 2020 10:07 pm
- Forum: Spyderco General Discussion
- Topic: First time sharpening with sharpmaker and need help
- Replies: 20
- Views: 2710
Re: First time sharpening with sharpmaker and need help
Here's a photo of that messed up side: bevel is mostly good towards the middle, (maybe a very mini line of sharpie not seen on camera), but the choil and tip have inconsistent sharpening and leave large sharpie marks. Link: https://imgur.com/a/YFO4NjK EDIT: There are two images. The first one (tip f...
- Thu Apr 02, 2020 10:04 pm
- Forum: Spyderco General Discussion
- Topic: First time sharpening with sharpmaker and need help
- Replies: 20
- Views: 2710
Re: First time sharpening with sharpmaker and need help
Thank you all for the replies. So far, here's what I've done: I spent a few hours trying to reprofile the messed up side with the diamond rods. I used the flat sides of the diamond rods at 30 degrees and used light pressure, and made sure my knife was perfectly vertical the whole way through. I made...
- Thu Apr 02, 2020 12:50 pm
- Forum: Spyderco General Discussion
- Topic: First time sharpening with sharpmaker and need help
- Replies: 20
- Views: 2710
Re: First time sharpening with sharpmaker and need help
Hi ManyReason, welcome to the forum! Sometimes the edge grinds come a bit uneven from the factory. From your description, it sounds like one side of your knife is a perfect 15 degrees, while the other is a bit more. Being uneven like that may make sharpening a bit annoying, but it isn't uncommon an...
- Thu Apr 02, 2020 12:45 pm
- Forum: Spyderco General Discussion
- Topic: First time sharpening with sharpmaker and need help
- Replies: 20
- Views: 2710
Re: First time sharpening with sharpmaker and need help
Thank you all for the replies. I will try continuing to rebevel. I did watch the Spyderco sharpmaker video via YouTube, all 4 parts. I will try this again to see if my results change
- Thu Apr 02, 2020 10:29 am
- Forum: Spyderco General Discussion
- Topic: I need some clarification before using the Sharpmaker for the first time...
- Replies: 39
- Views: 7394
Re: I need some clarification before using the Sharpmaker for the first time...
Hi manyreasons, congrats on your Sharpmaker, it is a great tool! The first thing you need to do is decide if you want to use a microbevel or not. Opinions vary but I almost always use a microbevel because it makes it ridiculously quick and easy to resharpen a knife...especially with the sharpmaker....
- Wed Apr 01, 2020 10:05 pm
- Forum: Spyderco General Discussion
- Topic: I need some clarification before using the Sharpmaker for the first time...
- Replies: 39
- Views: 7394
Re: I need some clarification before using the Sharpmaker for the first time...
Ah, I wish I saw your messages before I tried to reprofile my edge... I think it's fine though